The e revo will only turn one direction and sometimes when i try to turn it the other way it makes a clicking noise, i dont know whats wrong with with it. help!
Hello everyone,
I have a Traxxas Revo 3.3, that was running flawlessly last night might I add, and now it wont start at all! I can't even get the glow plug to light up. I am pretty familiar with nitro, but this is completely boggling my mind. Here are the details of my situation and hopefully...
After few nightmare day of trying tune the engine(with no luck) I think there is something wrong with my throttle.
As you can see on the video the servo is making strange noise and its not opening the carb full. I can push it and open it full with my finger but the servo wont do that. Is the...
As per title, is there such a thing as a setup board that can be used on the nitro revo (2.5 or 3.3)?
I used to know such things, but time away has seen a few things forgotten.
I saw awhile back a few guys were running the Trinity copy exhaust. Was just wandering compared to the real deal are they. A friend wants a Trinity but obviously they are hard to come by. I currently have his 3.3 Revo running a Picco maxx.21 tore down for some repairs and cleaning. So he wants...
Hi All!!!!
Well, my Revo rebuild is very nearly complete! Bought as a roller and chatting to you lot on here I've added the following:
THS Big Block pipe (for rear of Revo)
Big Block adapter for above
Savox single steering servo
17Tooth clutch bell (36T spur existing)
Ofna Mount for Picco...
Hello everyone, I am new to this forum and new to the Nitro RC world. I'm sure this has been asked before but I am in need of a good reliable motor to replace the HPI .25 in my savage. My local hobby shop only directed me to HPI brand motors that are a bit much than I want to spend. I do not...
i noticed one of the screws which mounts the transmission to the chassis keeps spinning on me, it's the threads in the screw hole that are worn not the screw.
I read that some are using metal inserts to deal with this but was unable to find a link for the exact inserts i need.
can someone...
OK, first up I have a question.
Now, I may have dreamt it but I am not sure.
When I first started working on my revo upgrade project, I seem to remember something about a 3 speed gearbox. Didi I dream it, or is it possible?
next up, I need some advice and again, this goes back to the revo...
Following the last run of my revo, I decided that I would rebuild it.
Integral with the rebuild upgrades an attempt at a "unique" (to my knowledge) modification was planned...
I managed to acquire a few of the upgrades, then stopped due life and another hobby taking over.
This was all almost...
Hey peeps.
The 2014 has the big bore shocks made up of two springs. I believe this makes for a dual rate set up.
My question is which hpi or other brand spring make for a stiffer set up. Closer to like what the raven springs do for the t maxx.
I've been busy rebuilding my savage from the ground up, finished the body, only the wheels to do next, i hate that stretched out look so I'm not going to extend the arms and all that rubbish, 1/4 offset wheels with 3.8 tyres will do the job perfect, shouldnt strain all the running gear either...
So I bought a used tmaxx 3.3 from craigslist and I'm the third owner. after a year of sitting I finally got to work on the thing I tore down and sealed the engine,greased the difs,and just cleaned up the truck. After learning the hard way that the piston was directional I was able to get it...
Well I bought this MGT and believe it is the 4.6. I got this to be a project however it is clean and been taken care of so there is not much of a project there,LOL. A couple questions about them. Why do the brakes start to engage when you come down to 1/4 throttle? Is this a normal setting or is...
Hi, I'm being looking for some type of extended axles for my savage x 4.6 17mm hex I want to make it wider, I don't want to use the 5.9 ones any ideas thanks in advance.