monster truck

I have been having real bad half tank lean issues. I seen a video that shows that taking the fuel line that goes to carb off..seal that outlet on the tank..then drill a hole on bottom of tank and inserting a new fuel outlet fitting and then running to the carb from the bottom. Any experience...

Hey guys I had a 2.5 classic and been slowly upgrading things to the 3.3. Well last year I stripped a gear in the 2.5 tranny, so I finally got around to buying a 3.3 forward only tranny and converted everything over to the 3.3 chassis, so now the only thing not 3.3 is motor. Well I went to fire...

I just ordered a set of LCG extended TVPs, Savage servo plate, an extended center skid plate, savage motor plate and a set of servo mounts (along with an Alza bulkhead conversion kit.) I have looked and searched tons of threads on the Internet and can not find a list of replacement tanks to...

Hi, I have an old Revo 2.5 that I recently started converting to electric. I am currently running the stock transmission from my 3.3 Revo but I know that the high torque is going to shred my gears quickly. My question is: Does anyone know if a stock E-Revo transmission will mount to my 2.5...

I'm planning go BB on my revo since i have only problems with my trx 3.3 (air leak). What I'm planning to buy: OFNA JL .28 MAX THX Pipe OFNA Mount for Revo OS Medium plugs. In thoughts of driveline do i need to do any upgrades?

Heres my mgt's,first one is my primary basher,it does not get special attention other than the whoopin. Its about 11 yrs old. An the others. Mmgt.

I have posted this on a few other forums and just asking around to try to get as many responses as I can. Well after hours of reading tons of threads I'm still not sure what to do. I don't know if I should just Mid-Tank Mod it and get some extended TVP's and buy everything I need for prob...

Does anyone know if this is a good fit for the revo 3.3? http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXEPD0 For some reason i find that a lot of the bodies i see online do not have enough spacing between the front and rear wheelwells, i attached an example of one.

Can someone take a look at the pic and tell me what parts were used to make up the throttle linkage? My son bought a Revo with a Losi m26ss; the linkage is crap, hangs up, doesn't go WoT. I really like this set up but having trouble putting the parts together.

I don't know how u guys do it Iv been trying to get my tmaxx 2.5 going again can't afford a new truck like the people are tell me to do they say it's to far gone but runs good but it goes buy it self I just got my son the revo small one and now gotta get those other batteriy for that because the...

:thumbs-down: Hello, I have T/Revo 3.3...about 3 years old. Overall not much use, but recently have renewed interest with some local guys who are also getting started again. That said, I performed a basic truck service and now that the battery packs are fully charged, I started to test the...

I am new to the site and i am hoping someone can help me out.. I have tried alot! I am having issues starting my Savage X. I havent used it in a while and there was still a little bit of fuel in the bottom of the tank. I emptied it out and changed fuel. I am using 25%. When i try to start it a...

What rechargeable battery would you recommend I use to power my servos?

I had just put the steel 47 tooth spur gear on my savage x 4.6 and it are my clutch bell. I know on the hpi web site you need to use the racing clutch bells but don't know which number of teeth I should get. Which one should I get from 13-20?

I've been lurking for about a month since I got my Savage X 4.6. I have already got quite a few hop-ups and up graded both servo's. I am running a Hitec 7955TG for my steering and a Hitec 5565 for my throttle. I have only ran about half a gallon through it so far. It has broken in well and I...

Hi, I'm having a very annoying issue. The truck starts but only after I prime it up with a few pumps. Then it dies in a few seconds. Seems like right after the fuel that was pumped into the carb is burnt the truck dies. It's spits out plenty of oil and smoke. I've tried leaning it out and...

Hey Guys, I am looking at replacing my 8 TMaxx stock shocks with 4 1/8th scale shocks. I know UE used to make some, but I am not interested in spending a whole lot and the UE shocks were $119 last I checked, if you can even still get them. I know that Ofna LX1 rears used to do the trick, but...

Totaly hacked off with an f 4.6 engine just wont run right or tune got no air leaks got good back pressure good compresion did have new plug till it bernt out running 25 percent nitro will only start wen it rich basicaly factory settings so then it just cuts out as soon as u go near the trottle...

Hi, I'm sorry if this was posted I searched the forums and can't find them. I want to buy a brushless MT looking at the HPI Savage Flux vs the EMaxx Brushless. I want a truck that will be more durable and with fewer repairs. I'm going to basically run it on my home street and large backyard...

so a friend of mine wants to buy a truck, i showed him my t-maxx and he really likes it. so upon his search he has come across a hpi savage xl (used). we haven't checked it out yet,so wondering which would be better? I was comparing specs and hpi seems better,but going off manuals t-maxx is way...