So I got a revo on a trade, tried to start it but it wont do anything, the glow plug light just blinks on when you hit the start button, tried 2 different wands and both do the same thing, tried 2 different plugs and it does the same thing, ground is attached good, blue wire is intact. I just...
Hey everyone.
I am looking for a engine upgrade for a 20+ lb Revo. I am leaning more towards the LRP .32 as I hear it has ample amounts of low end torque. My Revo has a all-steel single speed tranny, spur & CB plus MIP spline shafts, Duratrax Lockup MT tires (a bulk of the weight), ERBE...
well through the winter I bought pieces and parts here and there and I'm now at about 95% done. Nothing real special but its got some of the well known things that break upgraded and just gonna run a stock 3.3 that I had laying around. But I powder coated the chassi mirror black and dyed the...
i can't get my revo to idle down. i bought the truck used and it runs good, just dont idle down like it should. it idles just at the point of moving. i have adjusted the idle screw and no luck. i have reset the hsn and lsp to factory but it still idles high.
so like title says crashed the revo broke the exhaust header right at engine and engine came off mount my question is there a way to temp fix the header with like thick waterhose with a ziptie or am i just out of bashing for a while i just got it running after 2 years any ideas that are cheap...
Hello all.
Finally nice out so tried to start the truck just now, I noticed no gas going to the engine. unplugged the hose going to engine, cranked it and no gas coming out of the hose. Seems I forgot to empty the lines after my last run last year and was gunked up. Changed the hose and gas...
I was thinking about using some jb weld on my factory 3.3 5309 Revo engine to hold on my pipe to the engine a after market pipe set is this a good or bad idea and why??..
Hey guys back again with yet another issue with my revo. Been going at it all day, the car was revving up without moving, i tightened down my slipper and replaced my clutch and now the car moves forward with throttle, but only for about 2 minutes then goes back to the same, revving without...
Looking for Tekno Revo carries #10141(just carries) or #1014(set w/hexs).
I really need 2 sets of 4 as I'm building 2 trucks, but I'm looking for whatever I can get.
Having clutch or tranny issues, my clutch bell spins at idle, my spring is good and have reassembled the clutch, i have no idea what to check next. The clutch bell just spins the spur gear at idle + revs up without moving wheels.
Hey guys, I have a great condition trans for the Revo or Slayer, I built it for a big block but went a different route instead! This thing is near bullet proof as every gear has been replaced with RRP hardened steel gears. Also has the hardened steel FOC. I will also be sending with it the 16/40...
I recently purchased a used Revo for $35. I'm not even sure what its missing but i do know it is missing quite a bit from the truck.I was able to get the engine running after i pulled it from the truck, but when i put it back in, it moved maybe 10ft or so and then it stripped the spur...
My revo 3.3 won't move forward and it slowly crawls in reverse I have tightened the spur mesh tightened the slipper clutch I had the transmission out while it was out I turned the spur gear and the drive shaft turns so I think maybe I am wrong to think the transmission is ok ...is there a...
So are the front and real differentials the same? I am just wanting to make sure I have a leaking front and a complete diff ready to drop in as a spare but am not sure if the front and rear are the same.
My 2.5 with a 3.3 is giving me a problem. All the wheels try to spin when i crank it. Pretty sure it is my clutch just making sure before i tear it down. Thanks!