TRADED!!
Ok guys I'm selling my RC10GT Cause I want to get my crawler going. It is ARTR all you will need is tx/rx and a battery/charger for the starter box plus the regular stuff... glow igniter, fuel, etc..
So here is the list...
OS .15 CV-R
RPM radio box
RPM body mounts
RPM bulkheads...
1. I've replaced the batteries with rechargeable batteries. it gets like 20 feet away and stalls out. Whats the problem?
2. is there a way to stop the throttle from staying at full throttle? it gets out of range and stays a full. so i have to go chasing after it.
3. where can i buy a new small...
I have a rc10gt and i have some questions:
1. What is the right temp. in F. that it should be running at?
2. I can start it up and it runs perfect then when i let it go, it gets 5 feet away and stalls out. it starts right back up on the first pull and does the same thing. I just replaced...
Alright, so I've currently got a few year old Losi XXX-NT that I just recently starting ripping around with, and decided to upgrade my power. I bought an O.S. Max .18 motor and the thing RIPS! However, the car is a little bit old for the power it's getting and my diff won't stay tight etc...
Hey guys I'm looking for something like a RC10GT Or possibly a buggy. I dont want to spend more than 150-200. Let me know what you have. Only Nitro I'm looking at getting into racing. Thanks!!!
I have a used rc10gt with mip cvds. I am rebuilding the truck and I just want to clean the cvds. I was able to get one apart and I cleaned it with hot water and dish soap. I can't get the pin (in the joint) out of the other cvd though. Set screw came out fine, but the pin deal wont slide out. I...
Hey guys I am new to Nitro, just picked up an AE GT2 today and when I first started it up, the thing was revving up pretty high, I know that isn't good for a new motor, (I think it was pretty high at least). I pulled the fuel line a couple of seconds after it ran. When it was on the wheels were...
To make a long story short, I blew up the rear bearings in my used rc10gt today. I just have some questions before I place an order at my lhs. I believe I have the 3/16 axles, but I could be wrong.
1. Are the rpm oversize bearing carriers good? Is it correct that they eliminate all of the...
i got the parts for my GT and i finally got them in and together and now the problem is the electronics dont work right...the servos and the controller are not communicating with each other.. the servos twitch when i turn them on but when i turn on the controller... the controller does nothing...
I got a factory team RC10GT and I'm looking for a good engine for it (i call the truck "it" cause it's a beast). I got a old OS .12 CV and shes getting tired. So i need something with a little more pep. What would you guys recomend.
I have a RTR GT2 with the stock .15 AE motor I beleive it is. I have read various things about the shaft being diff than other motors and you can't use the diff eliminators on the market. I am wanting to race this truck and figured the pull start has to be coting me some power. Can i just take...
hey guys i have heard of some guys sticking a 2 speed made by hpi in there rc10gts i was wondering if ud ever seen this or know of possibly another way to do it?? thanx
i got an old used rc10gt for next to nothing from a friend of mine and spent over $200 bucks on tower to get her moving again put it all together last night took it out this morning and rounded the spur but i can't figure out y
the clutch bell mesh to the spur was good and they both looked to...
i just got an old rc10gt from my buddy but i cannot find rims for it for the life of me i bought 2.2s but then the hole in the center was to big for my bearings and then the back ones have a wierd cross thing in them ??