busted the factory clutch up some how so i went with hot racing's aluminum flywheel and 3 shoe upgrade (for my 3.3 revo) i see a noticeable improvement in acceleration. and my steel spur gear is on the way. my only concern is why i have to clean out my carb every tank or so for it to run... I'm...
trying to decide on what clutch to pick up.
from reading it looks like the buku, m2c and werks are all good.
i do not race just looking for something that will grip well, i was leaning towards the m2c as i read it has great grip, the price is good but i wish it had a top pin brace.
what do...
Good ol' Chickenman advized me to get a 17/36 clutch/spur set up. So I did.
I have a standard 22t clutch bell on my Picco (originally from my T-Maxx). I got the 17t hardened steel clutch bell from traxxas. They have a number of slight differences:
'][/URL]
'][/URL]
Sorry the second pic is a...
Just stripped the second clutch bell in less than a quart of fuel. Being new to the hobby I chucked it up as parts wear out blah blah blah. Now the second one stripped out in two to three runs. Why is this happening? Is the clutch and spur spacing off? If so any techniques on spacing? Btw metal...
Just wondering if the Intergy 3 shoe cluch upgrade is any good or better than stock
http://www.integy.com/st_prod.html?p_prodid=4361&p_catid=29&ratesortby=New#.U64T73gazCQ
I am trying to figure out if the O S 18TM crank will fit in my existing setup on my hpi bullet mt. Not trying to fit the crank in my existing engine just clutch ect....
Link to crank: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXHKV4
Link to current crankshaft...
while out bashing around this weekend, the clutch decide to incinerate @ full throttle. I found some parts. blew up then took out the spur gear. From your opinions what clutch should I put in? Stick with stock unit again or go with?................. looking to what some of you have swapped to...
Hey guys, so on my revo the clutch bell sticks out to far past the spur with the picco on it. What should I do or what have u guys done to fix this issue. I cut a slight bit off the front of the teeth but seems to be taking a toll on my spur gear. Any ideas would b great. Thanks all.
Hi to everyone, I want to thank all the good people for help on my last post, many thanks. My problem is that the slipper clutch hub had melted on my son's HPI rush evo Does anyone know if it's possible to make do with any other hub even if a little modding is needed? Any suggestion's most...
Hi i have a traxxas slayer pro 4x4 short course truck. Well i replaced the stock slipper clutch because i lost 2 out of the 3 pads. So i replaced it with the metal one and was wondering how tight do i tighten the nut??
I just upgraded to HPI Racing aluminum clutch shoes on my Savage X F4.6 (purchased new in February 2014) and I have had issues with a clutch holder and shifting. I believe I have fixed those issues, but I am curious what to expect with the new clutch shoes compared to the stock shoes so I can...
Evening everybody. I have a Savage X SS with a K4.6 in it. Last week I was out bashing and the truck just stopped and wouldn't move. I thought the slipper came loose. Upon further inspection I seen the clutch bell was chewed up. When I got home I checked to see if the motor mount screws...
I have a thunder tiger 1/8 off road pro version competition buggy and it was fine yesterday until i throttled it and the engine was screaming but not going anywhere so i tightened a few screws that was loose and it worked. I took my buggy out today and it wasn't moving anywhere i no what the...
I have been using the BUKU composite shoes and a Robinson racing clutch bell but the clutch-bells teeth still bend or strip :angry:, the teeth alignment is good and i used the paper trick, is there an extra super strong clutch-bell for the savage xl 5.9, or a way to prevent this from happening -...