Looking at eBay at slipper clutch rebuilds and found a Slipper Clutch Eliminator, i was curious if those worked for nitro and what the opinion is of them out there. Thanks guys!
OK. I have a good question about my clutch bell.
I have a T-Maxx 3.3. My stock bearings are 5x11x4. I want some upgraded bearings and noticed several places listing the clutch bearings as 5x10x4. Should I get a clutch bell for 10 mm bearings or are the 11 mm bearings better? Anybody else ever...
Does anyone know if the Schumacher Fusion 28s 3 speed clutch bell is thread and if the gears can be removed? I have searched everywhere and I cannot find any info on it. I know its an older car but someone has to know lol. From the pictures it looks like the gears are threaded pinions.
Hi i have the following buggy. The issue is that, the engine starts fine but when i put the buggy on the ground it doesn't even move.
Losi 8ight 2.0 RTR buggy with 350 engine
2 shoe clutch
Checked the diffs and tranny- the car free rolls without any problem.
It moves only slightly at full...
So... I fried my clutch. The bell looks fine, and I have a few other things to fix while I'm in there, but I'm wondering what shoes to get. Stock, alloy, or whatever. What are you guys running? Stock Savage X 17/47 gearing.
hi, so I've been hard at work repairing and giving some TLC to a second hand Sacage XL, I've kept the existing 52 tooth spur gear and got a 19 tooth clutch bell, however they mesh far, far too much, there is barely, if at all, any play in the gears, and I've wedged the engine as far over as...
I have experience with an OFNA Dominator. On this vehicle there are two gears on the bell that drive the two speed transmission. On this vehicle, the two gears are threaded onto the clutchbell, and can be unscrewed as a unit. Is this how they all are? I also have a Savage XL, is the gear...
Hi all has anyone else had this problem I ordered a brand new 8ight-t from modelsport went to set up the clutch for right bite but at the point of no more adjustment the nut won't tighten any more I eased off so it slips then turned it back bit by bit but the clutch is still slipping and is...
Can anyone help me on this one? I'm looking for a 22t mod 1 clutch bell that will fit my Savage. Looked up and down the internet for it and couldn't find one. I pray I have a chance.
Cheers AssyrianSavage.
I'm trying to install the clutch shoes on an Monster GT 8.0 motor. I cannot figure out how to attach the springs properly to hold the shoes in. I have installed clutch shoes that have the groove on the outside of the shoe before, but I can't figure this one out and Team Associated is no help at...
Hello,does anyone know if i can replace my slipper clutch with a metal one as the plastic ones wear out to quickly,its on a xcellerator nitr
o 1.10,any info would be great.
What up fellas. I got a Savage Xl with a LRP .32 in it. Problem is the slipper clutch keeps slipping. I tighten the nut down but after a minute or so the thing is just spinning again. I've put lock tight on the nut and that still don't help. Any suggestions on what I can do to stop this? Should...
I'm not very familiar with rc cars, especially Nitro ones but I offered to try and get one running for a friend who had one collecting dust in his garage that he'd been given years ago.
So far I've had to replace the one way bearing, the roto start unit as it had lost 3 teeth on the gearing...
looking for a way to be sure the alignmenet between the spur gear and clutch bell are square? I have a little more play/adjustment since i had to extend the holes some in order to shift the center gear box up.
the only idea i had would require two laser levels that i dont have so hoping there...
I got an rc10gt from a coworker with a still in box Picco .12r sg. I've found that the threaded portion is 1/4-28. I've measured the shaft where the clutch bell would go and it's .195 and the bell is .313. Where would I get bearing to fit that? How else could I mount the clutch bell? Is there a...
I had just put the steel 47 tooth spur gear on my savage x 4.6 and it are my clutch bell. I know on the hpi web site you need to use the racing clutch bells but don't know which number of teeth I should get. Which one should I get from 13-20?
Hey Guys,
I was cleaning out the RC room and came across these clutch rebuild kits brand new in the package. I do not have the truck any longer so I figured I would offer them up to someone who could use them. I only have one pictured, but I have 3 total. All Brand new. I am asking $20+ free...
I recently purchased the 14t vented clutch bell (link below) and wanted to confirm the bearing size for it.
I am using 5 X 10mm bearings but they seem slightly loose to me, and i do not have any 5 X 11mm around to try them out.
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXLST6&P=Z