hello once again... it seems that my cooling head has had a run in with some pavement, and at first glance, i thought it was just the motor mount and the mount plate that broke. but when i begain the disassembly to put in the new parts, i discovered that my crankcase is cracked. the crack isnt...
Just has my first encounter with a curb and I need to replace the left rear upright... How do I transfer the old bearings into the new one? Thanks a lot for your help.
Got a V-spec coming and will replace the bearings after break-in. Just wanted opinions or to see what you guys might be using. I know EBmods uses the TKO ceramics but I'm not totally sold on ceramics. Cost isn't much an issue since they are very close in price for the set.
does anyone know if the RS4 RTR3 evo comes with rubber sealed bearings, or metal shielded bearings. i checked hpi and it only says "ball bearings" doesn't way whether they're sealed or not. searches on here also didnt come up with much. the ones on my car look like sealed bearings, there is a...
I've been looking around to replace the bearings on my Ofna buggy. I've found the following on Tower Hobbies:
- 5x10mm: Actual Dimensions are (5x10x4)(Inner Diameter/Outer Diameter/Width)
- 8x16: (8x16x5)
- 6x13: (6x13x3)
- 7x19: (7x19x5)
- 5x8: Couldn't find actual dimensions
As...
i need some new cleutch bell bearings i i want to get avid bearings. i have heard about them allot but are they as good as they say they are? and why are they so cheap if there as good as they say they are? if so let me know plz
I'm thinking about switching bearings, and I know of Boca Bearings but I've been looking around on the net and read some horror stories of damaged engines and bearings seizing and getting totally ruined. Which bearings are better to use? Swiss? Ray's?
Hey guys,
As I was replacing the faulty kingpin on my CRT, I got to thinking about something. The only place on the truck that does not have bearings are the front C hubs where the kingpin holds the steering knuckle in. Ofna uses metal bushings. Does anyone know if they make a bearing set to...
Hey, what gives?? I have a Mayhem and I've been blowing clutchbell bearings everytime I run it. So, I'll get about 7 tankfulls before the bearing is so gone that it starts to grab and will stall my car. Anybody else have this problem; what's the
The other day I finally ran my Rc10 gt on some dirt :devious: I was having a blast other than my tires blow and wouldnt get much traction. Anyway I decide to launch it up this huge embankment. It must have went 8 feet in the air and flew over 10ft in distance.When I drove it out of the weeds it...
Hey Guys
I got my son a E Rustler. He wants a set of my Pro-Line wheels and tires from my GT.The back fits fine,but the front wheels need some bearings.Does anyone know what bearings it takes??
Thanks
Stan
I was out running my RC10GT and it stopped running. When investigating it I noticed the spur gear was stripped so I figured my enging slipped because I had just worked on it and reinstalled and maybe I didn't tighten it down enough. In any case I replaced the spur gear with a new one and reset...
New stuff for Revo.
Revo Axle Carriers & Oversized Bearings
(Includes oversized bearings, carriers, & setscrews)
Blue Revo Axle CarriersRPM axle carriers for the Traxxas Revo have been painstakingly redesigned to improve the durability, strength, and reliability of these much-abused...
Are 1/8 clutch bell bearing fairly universal size or do they differ from one make of bell to another? My CB bearings in my S3 are shot (think they got rusted from the last time I hosed her down) and I'm thinking about taking the bearings from my .26 T-maxx since it's down right now anyways. I...
Help. I just got a new OS-18TM for my REVO. Broke it in like the last 6 RC engines I have. First day at the track and I smoked 2 one-way bearings and 2 pull starts. I checked the starter shaft and it seems like a sloppy fit in the bushing. Do you think this could cause the problem? I hate...
ok, i smoked one of my clutch bell bearings, and i can't seem to find them anywhere. i can find the clutchbell and bearings but all i need are the bearings.
does anyone know where i can get some bearings for a hyper 7 8 port on a PBS?
thanks in advance,
Monas :cheers:
I got a bearing kit for my rustler it came with the front and rear wheel bearings and some smaller bearings that i have no idea were they go anyone lend a hand here it would be appreciated. :cheers: