Not sure if everyone knows about this or if I am allowed to post this but figure I will try to pass some savings on. Bocabearings.com is running a .99 per bearing special for regular replacement bearings. The whole kit for my Revo was $31 with free shipping. I figure I will put some good regular...
Not just the engine bearings but all of them...
How do you tell when they are stuffed...??
I'm holding the inner smaller ring while turning the larger outer ring on my RPM wheel bearings and they dont feel real smooth...
And whats the best way to grease them...??
how do you make sure the...
It's been a while sinced my last post (domestic duties/work) but have managed to get some bash time in. Since i got my 4908 3.3 I've had the newbie struggles of tuning and driving. but am now becoming fairly competent at both! Recently though I've been working on suspension tuning and managed to...
So I was racing last weekend, the picco 26 was tuned to about 220 degrees and it was running great in the last two races. went to warm up for the main and flying down the front straight and it just shut off! Then, it would only start if i held the throttle about 1/2 open. I knew some thing...
So I pulled the CB and flywheel from my .32, so I could put them on the Losi 454 when it gets here, but it looks like I'll be ordering a few parts first. Clutch shoes are worn pretty good, so it looks like I need a CB and shoes. yay.
ok so the prob is that every once in a while my e clip on my clutch nut expands and i lose one of my fifteen dallors bearing,I tried patriot rc beraring with about 1 tank and they fall to peaces,I need a heavy duty 3/16x5/16 flanged bearing that is goin to make me not want to sell my truck...
I have a Tmaxx that i got used. Tore it down... chassis needed repairs, so I purchased some bulkheads and ss screw set. I went through truck to test for air leaks and the front bearing has a blowing bubble leak... Also missing oring on pull start.. but no leak from there. I purchased a new 3.3...
hello everyone, well i stripped the 2.5 revo that i bought last week.everything was really dirty but in good condition,so the last thing i had to do this morning was give the mill a good going over,first thing i noticed was the needles were extremely rich,so figured an air leak right?then i look...
I had a wheel bearing explode on me today and so I decided to replace them all. I found some by a company called Xtreme Racing and they are ceramic for 55.00 for 10 bearings. All others where regular bearings at a much lower cost. I don't know how long to expect cheap bearings to go versus...
I have a 3.3 and the end bearings are starting to leak fuel, just like the 2.5 always does.
Are they the same bearings as the 2.5??
Where can I get a reseal kit for the 3.3
THANKS!!!!
I'm going through my t-maxx 3.3 transmission and replacing the bearings. I'm looking at kick ass r/c parts for bearing so my question is what is better rubber sealed or metal sealed bearings?
I am in the process of breaking in my .27 sirio, the first three tanks went fine. After i had to do a 3/4 throttle for a few seconds the truck just felt bound up. The engine was running about 225-235. I decided to check everything out and when i did i found that my OWB was completely trashed. i...
had a couple ?'s about bearings. what is the benifit of ceramic over metal? And is there realy that much noticeable drag on rubber shielded bearings? I need to buy some new wheel bearings and just wanted some info first. thanks in advance.
So I replaced my axle carriers with RPM's about a week ago and got about an hour of runtime on them in a dirt pit and when I came in to shut it down it sounded like their was tons of sand stuck between the axle and the carrier well I took it apart and it wasn't all that dirty so I removed the...
My clutch bearings went again and I was wondering if a ceramic bearing would help to maybe get 3 gallons instead of 2 before I have to replace them. I went to ask the owner of my LHS but they said that no bearing can take the being heated then cooled so many times. Is that the case, Or is this...
help
Shattered an axle yesterday and lost the wheel bearings in the process....
Team associated parts listing does not even show the bearings that go in the front wheels on my GT2
Its probably a common / generic size.... i just need help so that i know what to order!
Thanks...
I have about 2.5 gallons in my savage and clutch bell bearings went. I got some of them but should they fit in snug or barely stay in there... they barely stay in the bell. Also, My clutch shoes went, Should I upgrade to aluminum or stay with the teflon shoes? Also should I stay with the same 3...
I am going to order These clutch shoes, at least I am planning on it.
What do you all think?
I also need to know what springs to use for these shoes.
These will be for my savage with OS30VG
How important are a certain name brand of clutch bell bearings?
I've ordered some before, but I can't...
I ordered bearing listed specific for my engine Item number: 260366782799 on Ebay from http://myworld.ebay.com/2rideornot2ride/
Well I get and they are wrong needed sealed front bearing got shielded in place needed shielded rear/internal got sealed in its place.
Well thinking that the...