bearings

ok getting annoyed now, everytime i drive my rc10gt it blows a CB bearing iv got it slightly shimmed so that there is a gap about the size of a mechanical pencil lead, they just keep on grenading. I'm running an OS .12 cv-r I'm also buying the best bearing my lhs has. any suggestiongs would...

What Clutch Bearings do you guys run i have been having bad luck. has any one herd of "Advix" bearings or something like that? Thanks, -Ice

I didnt know i needed them until now, when I'm ready to put it on. what ones do i need and show me where to buy them.

Hey guyz, Is the cam type servo saver good for racing, does it really help. And i also saw the ball bearing set, 4 ball bearing for 14 bux, ouch. Do these do anything and really help, or really just a stupid investment Savage xtm 247 pro

Well, today I decided to tear down my S710 completely and rebuild the clutch on the Mugen X12 as well. Everything was going well till I got to the clutch. I pulled off the clutch bell and a whole lot of little metal balls came out. I blew up the 10x5 bearing in the clutch! AAAAAAAACK...

Well, after hours of searching, here and with google, I only found one place that sells an actual kit for thr R40 and that I found here. ONly thing I do not like about their site is that fact it does not actually say it replaces all bearings and does not list what bearings are included. I...

my O.S V-spec is at exactly one gallon of fuel right now, and i have it torn down for inspection and cleaning. I've read online that a few people have had problems with premature bearing failure, some as early as one gallon. most people just throw in a set of boca or nova bearings before or after...

what are the size of the side bearings and the font bearings for the differential because there are several that i think are it and i dont want to be wrong!!!!!!!!!!! plz help! thanks, tyler

does any one know the size of the bearings that go in the servo saver.. many thanks

Hey guys I'm almost done with building my new engine i dont know which way to install the thrust bearings do ballbearings that are between both rings face the engine or should they go away from the engine thanks in advance.

I would like to give my nitro tc3 a complete overhaul how often should i replace my bearings or should i just clean and oil. I race my tc3 2 times per month the car is atleast two years old.Thanks for your help

Found these just not sure if they are any good. What do I look for? Anything better out there?

So far I've only tried it on my bearings but it did wonders now they spind better and longer then ever before! I was looking on my Pop's room to see if he had a multimeter in there and i came upon this stuff this is my new RC lube screw the trinity purple! Ill try and see if he remembers where he...

I'm just checking to see what everyone else has tried. I typically get about a gallon of run time through my maxx and the Diff outdrive bearings are fried. I believe these are the 10mmX15mm bearings. I've tried 4 different brands and 3 different styles. Duratrash teflon sealed, Traxxas metal...

how would i got about replacing bearings on my DuraTraxx Maxium ST?.all the suspension components are tight,but yet the tires have serious play in them.

Hey guys, I have managed to lose a ball bearing in my savage transmission and I think this is one of the big reasons for me losing spur gears all the time. Well I am looking to see if anyone know's where to get them locally. I am having a tough time. I am off to try my local hardware...

both of my clutch bell bearings went bad this weekend. i've had them in for about a gallon with the stock 3 shoe clutch setup, and 5 or 6 tanks with the fioroni sliding clutch setup (carbon pads)....could the extra heat from the sliding clutch caused the problem with the bearings, or do they...

OK, I'm trying to replace the engine bearings in my 2.5. I keep breaking glow plug elements, and read somewhere that bad bearings would cause it, as well as lean conditions. Fixed the lean condition, but still breaking plugs, so I have new bearings ready to install. Only problem is that I...

I've got a full set of four stock Maxx axle carriers/Knuckles in Excellent cond. They come with 8 new sealed bearings. I have no use for the great bearings as I run RPM Knuckles. $22.00 Shipped VIA standard USPS First Class. Buyer pays upgrade to Priority

What bearings for the Savage should be added/replaced besides the steering upgrade? If any, part #'s would be helpfull. Thanks