• Welcome to RCTalk! 🚀

    Join the #1 RC community where hobbyists connect, share, and get expert advice on RC cars, trucks, boats, drones, and more!

    • ✓ Friendly & passionate RC enthusiasts
    • ✓ RC tips & troubleshooting
    • ✓ Buy, sell & trade RC gear
    • ✓ Share builds & upgrades

The Daily Rant Thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
paytonimusrex said:
had my first infusion of my new meds on friday went well for the most part, except the first iv needle they couldn’t get the vain had to run a different one and then I fainted shortly after lol
Click to expand...
Infusion? Damn, dude! I hope the meds works for ya.
 
Xraycer said:
Infusion? Damn, dude! I hope the meds works for ya.
Click to expand...
yeah so do I lol, I have ulcerative colitis unfortunately so the i’m taking biologic medication that requires an infusion now, hopefully the meds help and I reach remission though
 
paytonimusrex said:
yeah so do I lol, I have ulcerative colitis unfortunately so the i’m taking biologic medication that requires an infusion now, hopefully the meds help and I reach remission though
Click to expand...
Dude!

I'm sure you know this, but: That Sucks! 🤪

I'll keep you in my thoughts/prayers!
 
Wtf savox
I literally just got this servo at my house 2 hrs ago.
PXL_20241230_211821867.MP~2.webp
 
Look at this. Servo mounts. One screw goes fully in and the other doesn't and it gets stopped by something inside the mount. Both screws going through the bottom(up from the chassis) are the same size and length. As the screw got tighter it was twisting the tab on the servo. If I recall this right, that servo mount wasn't like this when I took the old servo out. Hmmm.


PXL_20241230_213122315~2.webp
PXL_20241230_213116372~2.webp
 
Can't find a MIP gen1 2mm speed tip in Aust to replace the one I broke 😕.
Only a ball end available. Has anyone here used a MIP ball ends?

I can get the gen2 but I won't have a matching set then and they are more expensive.
 
I only use ball ends when I absolutely have to. They aren't great for breaking tight screws. There just isn't much contact area on the flats inside the hex socket, and will strip screws a lot easier. But as far as ball end drivers go, I imagine the MIP ones are top notch.
 
This fireworks stuff is worst than the flying bats! And can no longer identify members now that the masks completely obscures the avatar. 👎
@WoodiE
 
Xraycer said:
This fireworks stuff is worst than the flying bats! And can no longer identify members now that the masks completely obscures the avatar. 👎
@WoodiE
Click to expand...
Who's that talking? 😆😂
 
Xraycer said:
This fireworks stuff is worst than the flying bats! And can no longer identify members now that the masks completely obscures the avatar. 👎
@WoodiE
Click to expand...
The firework animation wasn't so bad. The snow animation during Christmas that blanketed the whole screen made me want to close my head in the elevator door at work. 😂

One could argue I should've been working and not browsing RCTalk... but what can I say. lol
 

Similar threads

Cheetah928
The top speed thread!
2
Replies
22
Views
3K
CJSRCLIFE
CJSRCLIFE
Ramp addict
looking for a video snip from a thread.
Replies
2
Views
88
fstnd
fstnd
Littlemotor
The official “What’d ya get in the mail today?!? thread!! 🤩
45 46 47
Replies
928
Views
24K
CJSRCLIFE
CJSRCLIFE
Ritz413
The luck of the Irish is mine!
Replies
10
Views
396
Ritz413
Ritz413
majin
Fight night with the wife
Replies
10
Views
242
9x19
9x19

RC Builds

Back
Top