-
Welcome to RCTalk! 🚀
Join the #1 RC community where hobbyists connect, share, and get expert advice on RC cars, trucks, boats, drones, and more!
- ✓ Friendly & passionate RC enthusiasts
- ✓ RC tips & troubleshooting
- ✓ Buy, sell & trade RC gear
- ✓ Share builds & upgrades
New Losi tenacity DB pro
- Thread starter Brandon1
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
brushlessrc
RCTalk Rookie
- Messages
- 20
- Reaction score
- 19
- Points
- 33
Well the chassis braces for the SCTE do not fit our Tenacity buggies. I bought STrc aluminum braces for the SCTE and they don't fit.
But...
I installed the DE mudflaps, aluminum rear hubs, front spindles (front knuckles are sold out EVERYWHERE), Traxxas waterproof receiver box, Savox 1210Sg servo, power RC clamping horn, steering assembly bearings, premounted proline badlands and RPM skid plates do fit.
I'm stoked at the difference in the steering and the tires!
But...
I installed the DE mudflaps, aluminum rear hubs, front spindles (front knuckles are sold out EVERYWHERE), Traxxas waterproof receiver box, Savox 1210Sg servo, power RC clamping horn, steering assembly bearings, premounted proline badlands and RPM skid plates do fit.
I'm stoked at the difference in the steering and the tires!
Last edited:
brushlessrc
RCTalk Rookie
- Messages
- 20
- Reaction score
- 19
- Points
- 33
Looks good!!
brushlessrc
RCTalk Rookie
- Messages
- 20
- Reaction score
- 19
- Points
- 33
I’m still waiting on my Savox 2271. It was supposed to be delivered Monday and got lost. Another one on the way. I installed the Exotek aluminum ball bearing steering. It’s very smooth.
http://www.exotekracing.com/tenacity-pro-hd-steering-set/
http://www.exotekracing.com/tenacity-pro-hd-steering-set/
Uncle Pete
RC Newbie
E- fanatic,
does the ceramic bearing kit include bearings to replace the steering bushing. Thanks
does the ceramic bearing kit include bearings to replace the steering bushing. Thanks
E-fanatic
RCTalk Racer
- Messages
- 112
- Reaction score
- 116
- Points
- 118
- Location
- Hertford, NC.
- RC Driving Style
- Bashing
- Racing
- Flying
Yes
I just received the TLR334000 o-ring set for aluminum shocks. My plan was fo go 42weight oil as I just bash this bad boy around.
However, after getting them the packaging states they are bleeder o-rings. This makes me believe they are for the bleeder caps only, or will they work for our stock aluminum caps?
Thanks!
However, after getting them the packaging states they are bleeder o-rings. This makes me believe they are for the bleeder caps only, or will they work for our stock aluminum caps?
Thanks!
E-fanatic
RCTalk Racer
- Messages
- 112
- Reaction score
- 116
- Points
- 118
- Location
- Hertford, NC.
- RC Driving Style
- Bashing
- Racing
- Flying
You need the tenacity shock seals. That way they still have the bladder
Don't these stock shocks come with bladders?
Ok, I think I've got it figured.
I need the x-ring seal set. If I don't have the x-ring seals I'll still have to use the bladders. But the bleeder caps are not required.
Correct?
Have a few questions about fitment since I've wasted money buying cross platform parts before.
Will this STRC steering rack for the scte fit the tenacity?
I'm looking at these hinge pin braces for the scte 3.0, will they fit the Tenacity?
If those do fit, do I need the plastic bits as shown in the below kit? I do not see them in the parts assembly diagram. I do not want to buy the upgraded braces and find out I need those plastic bits.
Thanks!
Will this STRC steering rack for the scte fit the tenacity?
I'm looking at these hinge pin braces for the scte 3.0, will they fit the Tenacity?
If those do fit, do I need the plastic bits as shown in the below kit? I do not see them in the parts assembly diagram. I do not want to buy the upgraded braces and find out I need those plastic bits.
Thanks!
- Messages
- 82
- Reaction score
- 35
- Points
- 623
- RC Driving Style
- Racing
Might get one and convert it to the 3.5 Traxxas engine.
Great day in the dirt and mud today. Those rear mud guards and the Traxxas water tight receiver box sure came in handy.
Tore the DB down after and cleaned everything, dried everything, regressed and oiled. Feels good to check all the components of an RTR, making sure everything is to spec.
Tore the DB down after and cleaned everything, dried everything, regressed and oiled. Feels good to check all the components of an RTR, making sure everything is to spec.
Uncle Pete
RC Newbie
Does anyone have a spring diameter for this model. Thanks.
The manual states the spring sets are part number los233013. When I reference that number all I can find is they're 12mm springs.
E-fanatic
RCTalk Racer
- Messages
- 112
- Reaction score
- 116
- Points
- 118
- Location
- Hertford, NC.
- RC Driving Style
- Bashing
- Racing
- Flying
They are 13mm springs. Same as the losi scte 2.0. They losi 12mm springs that go on the scte 3.0 and the other 1/10scale trucks will not fit
brushlessrc
RCTalk Rookie
- Messages
- 20
- Reaction score
- 19
- Points
- 33
My buddy is having issues with the stock shocks. The piston E-clips come off at times. Anyone else run into this problem?
Last edited:
No not yet. I have not taken any crazy jumps yet though.
However, I have purchased the o rings for the bleeder shock caps but it appears I may have to get other things as well to be able to use bleeder caps and o-rings. I may just rebuild everything and get rid of the clips all together if possible.
brushlessrc
RCTalk Rookie
- Messages
- 20
- Reaction score
- 19
- Points
- 33
I haven't had any issues yet, either - but same as you I don't do any crazy jumping. That will be a nice upgrade, curious to see when you're done.
