The "what you broke today" thread.

[DavidB1126]

Horizon

Fixed

 

[332_RC]

I don't drink, blaze, RX or do drugs

 

[Doom!]

I don't drink, blaze, RX or do drugs

Me either.

 

[Cheetah928]

The crash was so hard it literally shoved my motor forward! I got one screw loose, but the other is stripped. Help!

Well I got it out. And while this is not a MIP toolset, it saved me a ton of time by getting some stripped screws out

 

[DavidB1126]

...

 

[Beer_Goggles_RC]

...

View attachment 257541

View attachment 257542

View attachment 257543

View attachment 257544

Did you tie it to your bumper and drag it behind the car?

 

[Tunedfrog]

I broke my diet today.

 

[DavidB1126]

Nah it's just these sweet things I got for a huge deal

Did you tie it to your bumper and drag it behind the car?

 

[DavidB1126]

I broke my diet today.

Well it's a holiday/day off. You deserve it

 

[Tunedfrog]

Well it's a holiday/day off. You deserve it

I find it more enjoyable to eat today and regret tomorrow than it is to starve today.

 

[Doom!]

Well I got it out. And while this is not a MIP toolset, it saved me a ton of time by getting some stripped screws out View attachment 257539

I have this set too.

 

[Cheetah928]

Nah it's just these sweet things I got for a huge deal

View attachment 257545View attachment 257546

Knew it was 3s lol. They're fun, but man they destroy tires quick. Or suspension arms and other stuff

 

[Ramp addict]

I got a set of ADU hinge pin retainers for my Daughter's Tekno MT48. I installed the A block Saturday to get her truck going. Today I installed the rest of them. The front screws holding the gearbox on were sticking out about 0.5mm. Did I not tighten them down all the way? Then I noticed her front titanium skid plate was gone. How do you peel a titanium skid plate off of a truck without even damaging the screws that hold it on? I'll have to ask her.

The missing skid plate is a Tekno-Ti.

 

[Littlemotor]

How do you peel a titanium skid plate off of a truck without even damaging the screws that hold it on? I'll have to ask her.

The missing skid plate is a Tekno-Ti.

You don’t lol…

 

[Ramp addict]

You don’t lol…

The skid plate is paper thin and has almost no screw overlap. I bet with a pair of pliers I could pull off the rear one.

 

[Littlemotor]

The skid plate is paper thin and has almost no screw overlap. I bet with a pair of pliers I could pull off the rear one.

I highly doubt that..

 

[Lukedavis]

The skid plate is paper thin and has almost no screw overlap. I bet with a pair of pliers I could pull off the rear one.

Try it! I bet @Littlemotor will pay for 2 new ones if you can!

 

[Ramp addict]

Try it! I bet @Littlemotor will pay for 2 new ones if you can!

You would think the screws would pull out first but they don't. I'm assuming the back end of the truck got jack and the skid plate caught the ground and peeled off. I had this happen with a bumper. Instead of breaking the bumper or pulling out the screws it bent an EXB Outcast chassis plate. I no longer have a picture of this but it's posted on our RC Showcase "Ramp addict's Outcast".

Found it!!!!

 

[DavidB1126]

Uhhh

 

[DavidB1126]

And this