my wrenching is going through all these parts that I have to figure out what’s up with what lmao
-
Welcome to RCTalk! 🚀
Join the #1 RC community where hobbyists connect, share, and get expert advice on RC cars, trucks, boats, drones, and more!
- ✓ Friendly & passionate RC enthusiasts
- ✓ RC tips & troubleshooting
- ✓ Buy, sell & trade RC gear
- ✓ Share builds & upgrades
Who was wrenching today??? What did you do??
- Thread starter STONER RC
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
my wrenching is going through all these parts that I have to figure out what’s up with what lmao
PewPewChris
RCTalk Addict
- Messages
- 716
- Reaction score
- 1,840
- Points
- 210
- Location
- Georgia, USA
- RC Driving Style
- Bashing
- Racing
- Crawling
- Scale Builder
- Flying
Honestly I was thinking about it last night and it very well be the motor gear slipped back some off the tension bolt and wasn't fully seated with the front pinion. I dunno, I've already got the front end apart at this point, so going to clean everything, regrease it, put it back together (hopefully correctly) and reseat the motor gear and see what happens.Have you isolated the axles and rotated each side individually to see if you could chase it down that way?
Grit in your gearbox could certainly make a racket! Is it just in the housing or did it reach gears?
Have you removed and tested bearings for smooth, crud free rotation?
Just a couple ideas!
- Messages
- 5,781
- Reaction score
- 17,821
- Points
- 1,795
- Location
- PittsVegas, NC
- RC Driving Style
- Bashing
- Racing
Doom!
Team Dust Devil
Community Leader
Lifetime Supporter!
Supporter
Excellence Award
Hospitality Award
Build Thread Contributor
RC Showcase: 6
- Messages
- 18,393
- Reaction score
- 44,474
- Points
- 2,690
- Location
- Central California
- RC Driving Style
- Bashing
- Crawling
- Scale Builder
- Flying
I need some new descriptors! This is going to be beyond freaking cool! 
PewPewChris
RCTalk Addict
- Messages
- 716
- Reaction score
- 1,840
- Points
- 210
- Location
- Georgia, USA
- RC Driving Style
- Bashing
- Racing
- Crawling
- Scale Builder
- Flying
bought parts for the slash, new axles and a new rear bumper but it didn’t come with screws for the bumper so I gotta go back and buy the screws tomorrow
- Messages
- 5,781
- Reaction score
- 17,821
- Points
- 1,795
- Location
- PittsVegas, NC
- RC Driving Style
- Bashing
- Racing
Was busy with a full plate’s worth of “other shiit” all day, so didn’t wrench on anything, but finally managed to sneak into a livestream I’ve been trying to make for the last year or better.. Even managed to get a couple replies in.. Also reaffirmed that my thinking is correct, and there are a lottttttt of hardcore racers that don’t know wtf they’re talkin’ about.. 
Pretty cool.. Also did some work with the track, diag’d a bad power supply for my blacklights that gave up apparently first thing this morning in the RC dungeon, and composed a well worded email to the manufacturer as I’ve got about 14mos left on my warranty for them.. Be nice to not have to buy another set from a different manufacturer. We will see. Back on the track tomorrow, and likely begin the knifework on the Mon-Tech crawler body in the evening..
Pretty cool.. Also did some work with the track, diag’d a bad power supply for my blacklights that gave up apparently first thing this morning in the RC dungeon, and composed a well worded email to the manufacturer as I’ve got about 14mos left on my warranty for them.. Be nice to not have to buy another set from a different manufacturer. We will see. Back on the track tomorrow, and likely begin the knifework on the Mon-Tech crawler body in the evening..
I gotta do some soldering tomorrow, i’m scared it’ll be my first time doing it too
wish me luck
wish me luck
- Messages
- 12,617
- Reaction score
- 29,669
- Points
- 1,933
- Location
- Jurassic Park
- RC Driving Style
- Bashing
- Crawling
- Scale Builder
Have a fan on and try not to breath the smoke. I've also had solder pop in my eye once. Good luck.
well that will make it interesting not having a fan
i’ll open the window I got to solder the battery leads then flip a and c on the esc before I solder the motor
- Messages
- 13,204
- Reaction score
- 25,191
- Points
- 1,950
- Location
- Bomb Pop Island
- RC Driving Style
- Bashing
- Racing
You weren't wearing your PPE?!?
You are disobeying OSHA violations Mr.
To be fair I wasn't either. Burned my hand by holding the jig wrong
- Messages
- 12,617
- Reaction score
- 29,669
- Points
- 1,933
- Location
- Jurassic Park
- RC Driving Style
- Bashing
- Crawling
- Scale Builder
OSHA? I'm taking a lunch break until it thins out. Might go organize the storage space.You weren't wearing your PPE?!?
You are disobeying OSHA violations Mr.
To be fair I wasn't either. Burned my hand by holding the jig wrong
about to do my first solder very nervous lol
I realized my surface is not the best to do this on just in case lmao but like I have no better surface rip
I realized my surface is not the best to do this on just in case lmao but like I have no better surface rip
Last edited:
not pretty but I think it’s good enough. what do yall think?
- Messages
- 13,204
- Reaction score
- 25,191
- Points
- 1,950
- Location
- Bomb Pop Island
- RC Driving Style
- Bashing
- Racing
If it works it works
Just always make sure, pull on the plug. Not the wire. Learned that the hard way
Just always make sure, pull on the plug. Not the wire. Learned that the hard way
I just did the heat shrink on the wire it should be good now time to the battery on the buggy esc should be easier though lolIf it works it works
Just always make sure, pull on the plug. Not the wire. Learned that the hard way
- Messages
- 13,204
- Reaction score
- 25,191
- Points
- 1,950
- Location
- Bomb Pop Island
- RC Driving Style
- Bashing
- Racing
You using bullets right? Yea they are easy to solder up compared to plugs
yeah I am this iron sucks it’s not heating right or something idk might just be idk what i’m doing and hoping for the best I hope this doesn’t make things bad
well I can’t get these caps on
it’s not heating right or something idk might just be idk what i’m doing and hoping for the best I hope this doesn’t make things badwell I can’t get these caps on
Last edited:
Too cold
I don’t think I did horrible but not the best either I think i’ll just pay someone at this point holy moly
I think i’ll just pay someone at this point holy molyI have the iron on max temp and held it on these connectors for too long for it to be cold I don’t get it
