Build Thread Lost in a Tekno MT410

[Lostinthewoods86]

Man, that thing looks like a piece of junk. You should just sell it to me and be out from under it!

Awesome build dude!

Thanks Grey!

Looks good on there mayne! Can the front body pins go down one more notch? She's got a tad bit of squat in the rear. Or am I crosseyed again today?

It can, I need to trim the body a bit more so it kinda fits around the bumper mount. It looks more off because the truck is really soft in the rear and it’s squatted as well. Need to adjust the spring collars a bit still

 

[WickedFog]

Thanks Grey!



It can, I need to trim the body a bit more so it kinda fits around the bumper mount. It looks more off because the truck is really soft in the rear and it’s squatted as well. Need to adjust the spring collars a bit still

@Littlemotor just wrote up a tuning guide for setting up your suspension. Maybe he can post a link to it for ya.

 

[Littlemotor]

@Littlemotor just wrote up a tuning guide for setting up your suspension. Maybe he can post a link to it for ya.

$5.

 

[Littlemotor]

$5.

@Lostinthewoods86 doesn't appear to appreciate my subpar trolling abilities…

 

[Lostinthewoods86]

@Lostinthewoods86 doesn't appear to appreciate my subpar trolling abilities…

View attachment 201480

I got distracted and forgot to come back to this

 

[Littlemotor]

I got distracted and forgot to come back to this

Youuuuuuu?!? No way brotha-I’m not buying it…

 

[Lostinthewoods86]

I updated that here I got the esc plate done for the most part, still gotta clean it up some more. Just gotta get this thing prepped for paint now

And get the wiring done too

 

[Littlemotor]

I updated that here I got the esc plate done for the most part, still gotta clean it up some more. Just gotta get this thing prepped for paint now

And get the wiring done too

Looks KILLER man!!

Personally-I’d grab some new bullets for the esc side, shorten those leads, and solder the new ones at a 90’.. Floppy ESC wires that aren’t soldered to fixed lugs loosen up quickly, and cause arcing/carbon tracking that burns up esc’s at the very least, and possibly the entire vehicle.. This is especially the case in a bouncy, short wheel base, flipping MT platform.. Would be a huge help considering the ESC is no longer on even the same plane as the motor, and will tidy everything up nicely to boot. Function AND fashion. Just my .02..

 

[Lostinthewoods86]

Can the front body pins go down one more notch?

Dropped it down two holes

Going to get the edges cleaned up some more then start drawing and mask it.

 

[WickedFog]

View attachment 201557
Dropped it down two holes

View attachment 201558

Going to get the edges cleaned up some more then start drawing and mask it.

Oh yes dude! THERE IT IS!

 

[Lostinthewoods86]

Here I go

 

[WickedFog]

Good luck with the paintjob!

 

[majin]

hurry up and show us!!!!! but take your time and do an amazing job. but aslo.... HURRY UP

 

[Littlemotor]

Oh yes dude! THERE IT IS!

I LITERALLY just said that shiit out loud.

 

[Lostinthewoods86]

Won’t be quite like the real one, but should be close.

I only gotta do one side right?

 

[WickedFog]

View attachment 201629

Won’t be quite like the real one, but should be close.

I only gotta do one side right?

You only need one good side and one good end to take some noce pics

 

[Lostinthewoods86]

Fixed a couple lines, bout to start laying on the mask

 

[WickedFog]

Wow. You knocked that second one out in just a few seconds

Looks awesome man!

 

[Lostinthewoods86]

Wow. You knocked that second one out in just a few seconds

Looks awesome man!

Thanks man!

My eyes are killin me now

 

[Littlemotor]

Thanks man!

My eyes are killin me now

Just wait until you start peeling mask..