what engine would be best for the k2

[pissant]

i am going into racing and bashing. what engine suits the k2?

 

[ImBroken]

If your going to be racing, you going to have to run a .21 mill. I would recommend the Sirio K mill... I've seen it first hand, & it's a beast....
Trinity .21 Sirio Kanai Edition

 

[pissant]

sounds good, ok dont want to over post. quesiton is what pipe would be good for this buggy too? also what servos would be good and tires?

 

[ImBroken]

I would recommend these. I currently run them in my Ofna Hyper 7 Pro PCR...

Hitec HS-645MG Ultra Torque - Steering

Hitec HS-625MG Ultra Speed - Throttle

As far as Tires, you have a huge selection from either Proline, Ofna... It's kinda your preference, & whats better for the kind of track your running on.

For exhaust, I've heard real good things about the OS pipe. I'll try to find the model # for ya... It's big $$ though.

 

[uDi_MP7.5]

For an engine i'd look at the most common buggy engines - RB WS72 and Nova P5
is your track small, medium, large etc? that's what you want to match your engine to.

and for a pipe, I'd grab an OS T-2050, I think that's what imbroken is talking about.
you'll never buy another pipe again..

http://www2.towerhobbies.com/cgi-bin/wti0001p?&I=LXBPK8&P=7

 

[ZANDOR]

i agree with uDi. the ws711 is a great mill.i have one.very fast and easy to tune....

uDi so you have run this pipe OS T-2050.how is it all around the power band.
low,med,high...

 

[pissant]

is this the same pipe what udi is running on his buggy? also will this pipe fit the Trinity .21 Sirio Kanai Edition??

 

[ZANDOR]

as for tires for all around bashing.I use proline knuckles..

 

[pissant]

ok well here is my list, does it look ok. I have one more question what shock oil should i run with and what diff oils should i run with??? http://www2.towerhobbies.com/cgi-bin/wto0149p god i almost forgot the clutch and flywheel, what would you recommend?? i seen those silding clutches are those any good???

 

[ZANDOR]

shock oil i use 35wt all around.and add shock spacers as needed.
diff oil iam useing 7k 5k 1k front to rear...

 

[pissant]

what kind of clutch kit would be good??

 

[ZANDOR]

iam running the ue.4 shoe clutch.has great punch off the line

http://www.unlimitedengineering.com/cgi-bin/store

 

[Nitro_Freak]

i urge you to look at xtm servos' you can get them super fast, super strong, or in between...for only 35$. price is insanely low compared to other brands.

here's a link to them:
http://hobbypeople.net/prdcls/servoa05.asp

there the 3 on the bottom.

 

[ZANDOR]

i urge you to look at xtm servos' you can get them super fast, super strong, or in between...for only 35$. price is insanely low compared to other brands.

here's a link to them:
http://hobbypeople.net/prdcls/servoa05.asp

there the 3 on the bottom.

the high tec servo 645mg is only 40$
go with hitec

 

[pissant]

does the flywheel come with the k2 becuase the shoes do?? also what clutch bell should i get?? also what kind of air filter would work on that engine and also what pullstart would work on that engine??

 

[AC48]

Correct me if I am wrong but I don't think you can put a pull-start on the Sirio engine.

 

[pissant]

ohh, then i need a rotostart?

 

[AC48]

I could be wrong(I have no experience with non-pulls) but I believe you will have to use a starter box with the Sirio.

 

[ZANDOR]

you need a starter box IMO. pull starts break.and roto starts blow one way bearings. a starter box will not let you down.and if your going to spend 300$or more then get an rb mill...ws711 or the c5..this is IMO

 

[pissant]

are rb mills anybetter then the siro?? what clutch kit would be good with the k2?