bit worried? help plz

[asg]

hey guys was soo exited tooday got ma rc nitro thunder tiger ts4n i hopefully brok it in how do u knw its fully broken in btw??

TWO SAD POINTS

I was told wen i rang the company i was receiving a two gear system it turned out two be a one gear i rang them up n was soo angry as i specifically asked them i cnt send it bk nw

second guys my back left wheel is a bit slugish and doesent move in unison with the rest at full speed i tested it on a box also............. wen idleling on a box it doesent move suumtimes i checked if its to tight but wen i loosen it it gets a tad beter but the wheel goes wonky (too loose ) wen i tighten a litle again its jagged movement not smooth???????????
can an1 help plz thankyou

 

[2revo1maxx]

You're gonna have to use punctuation and FULL words. I have no idea what you are asking. WONKY?

Ok I think I get it. Does it roll ok on the ground?

 

[asg]

I'm sorry i mean when i loosen the tryre so that it at least improves slightly its actually too lose because the tire moves uneven in a crooked fashion?
so i knw thats too loose but wen i tightn it to a reasonable amount equivelent to the rest of the tyres it shows sticking like symptoms? and when its running on idle on top of box that same tyre does not rotate in unison with the others?
please help please thankyou

 

[2revo1maxx]

I'm sorry i mean when i loosen the tryre so that it at least improves slightly its actually too lose because the tire moves uneven in a crooked fashion?
so i knw thats too loose but wen i tightn it to a reasonable amount equivelent to the rest of the tyres it shows sticking like symptoms? and when its running on idle on top of box that same tyre does not rotate in unison with the others?
please help please thankyou

Ok. Take out the rear driveshafts and spin the wheel bearings. There must be a problem with the bearings. If not then hook the shafts back up to the drive and spin the drive by hand. But it's probably the wheel bearings.

 

[asg]

hey i think I've found the problem but i dnt knw how to fix it 2revo? the inside of the alloy is scraping the two plastic joists that screw to the tyre (inside the alloy theres two plastic joists witgh screws) and theve been scraping in the alloy and its actually scraped bits of the two plastic joists i dnt know how to fix it tho it seems the tighting of the wheel is adequate?

 

[2revo1maxx]

You'll have to look at a parts list and decide what part you need. I know nothing about your vehicle. Glad you figured it out.

 

[Mickstix]

I'll try and help, but I'm gonna need a picture of what's goin on.. You have any pics of the problem area? If it's new, maybe you could get a new piece if something is broken?

 

[asg]

 

[asg]

hey guys got pics its actually a part inside the alloy on pic 2-3 its the black rod like component with a silver nut if you look at it you will see it kinda looks chamfered (sanded) because its been scraping the inside alloy.
the alloy is also quite damaged too due to the rubing and hitting
my other back tyre is fine?
how can i fix this guys thnx

 

[pyro29123]

the end of your tie rod is hittin the rim. it just looks like a bad design to me.

 

[asg]

is ther a way too mend it ?my other tyre is ok

 

[pyro29123]

is there a way to move that? if so try and move it away from the tire. if not i dont know wat to tell you.

is ther a way too mend it ?my other tyre is ok

look at the other side and try to see the difference between them. then try to get them the same.

 

[PaulC]

Can you email the manufacturer? If made on the cheap they may know of batches that have a problem and instead of recall them, they just wait till someone complains, then they send them replacements.

Worth a try.

Other than that, if you can't move it somehow, sand it down so it doesn't rub. That's a last port of call though.l

 

[asg]

k thank you ill ring them 2mrwill let u knw what they say

 

[pyro29123]

where is it hittin in the rim? is it the spokes or the inner part of the rim?

 

[RC Addict]

is ther a way too mend it ?my other tyre is ok

Are those lower arms adjustable? Hard to tell in the pic. Probably not. But you can crank in the upper turnbuckle. Your alignment is way out of wack and your wheel and tire are pushed out at the bottom. Read your manual--there is a chapter about proper wheel alignment in there. At least there should be...

 

[pyro29123]

looks like RC addict found how to fix it! i couldnt see the adjustment in the pics. it looks like the lower arm is adjustable but it looks like its almost all the way in.

 

[asg]

thankyou guys