Post your workspace!

Welcome to RCTalk

Come join other RC enthusiasts! You'll be able to discuss, share and private message with other members of our community.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Work space...
workshop03rs.jpg


The gallery...
shelfqueensrs.jpg
 
Awesome job man looks good!! This is my little shop. I need to get some of the peg board to hang all my parts from.
16223817180438006762275361836469.jpg
I like it
 
I need to clean off my selves. So all the cars and trucks can go up there. And clean up the garage a little bit give me more room. For more cars/trucks lol
 
Cleared out a corner for my work table and currently shopping for some shelving too. For seating i have my old desk chair but i was thinking a shop stool might enable me be more productive or at least give the illusion of being more productive...?
pornhub00rs.jpg
 
Cleared out a corner for my work table and currently shopping for some shelving too. For seating i have my old desk chair but i was thinking a shop stool might enable me be more productive or at least give the illusion of being more productive...?
pornhub00rs.jpg
Pornhub is a nice touch. I need to add that to my workspace :hehe: :hehe: :hehe:
 
Lmao didn't even pick up on that nice eye 🤣😂😅 like the new traxxas mate
 
Cleared out a corner for my work table and currently shopping for some shelving too. For seating i have my old desk chair but i was thinking a shop stool might enable me be more productive or at least give the illusion of being more productive...?
pornhub00rs.jpg


Dude that dewalt gyro screwdriver is awesome! I love that thing
 
Dude that dewalt gyro screwdriver is awesome! I love that thing
i was skeptical about the gyro feature but so far its exceeded my expectations and was real easy to get used to using. My only small regret is not ordering the one that came with an extra battery...
 
I just got the cheap hart screwdriver. Works well for what I need. Only wish you could select torque levels
 
Yeah the tourqe setting is a big plus. But any power driver will work just be carefull not to fast.and don't fully set it will end up breaking or stipping out the plastic parts they go into. I also use my 20v max dewalt drivers and drills as well
 
looking at all these inspired me to clean up my workspace lo and behold 5 hours later here it is
IMG_20210619_231128.jpg
IMG_20210619_231155.jpg
 
I wont use a powered driver unless its got a clutch. In fact I dont even like to use them on plastic. I've stripped so many screwholes that way. Usually though if I put my Tek4 on its lowest torque setting it wont strip anything even in plastic as long as its an m3 size screw or bigger.

Nice work space Dewalt!
 
I wont use a powered driver unless its got a clutch. In fact I dont even like to use them on plastic. I've stripped so many screwholes that way. Usually though if I put my Tek4 on its lowest torque setting it wont strip anything even in plastic as long as its an m3 size screw or bigger.

Nice work space Dewalt!

I agree. Using power tools is definitely a easy way to strip out plastic screw holes. Got to have soft touch on the trigger. And I also don't set them in all they way with power tools. I finish off with hand tools safer that way.
 
But the new or some what new dewalt gyro screwdriver with clutch is awesome. You have so much control. And it's so slow that u won't heat up the screws going in and melt or strip holes
16241902840207513892829025715155.jpg
 
But the new or some what new dewalt gyro screwdriver with clutch is awesome. You have so much control. And it's so slow that u won't heat up the screws going in and melt or strip holes View attachment 128360
Yeah i sometimes finish off the screws by hand depending what it is. This screwdrivers does look pretty amazing tho. One of these days when my Tek4 dies I'll definitely be looking to get one of these!
 
So after 2 days of moving yet more stuff from one room to another to make room for my crawler course tables, this is what my work space looks like. I have RC cars sitting everywhere lol.
20210804_233758.jpg
 
So after 2 days of moving yet more stuff from one room to another to make room for my crawler course tables, this is what my work space looks like. I have RC cars sitting everywhere lol.
View attachment 130490
Oh man that's always a fun time. And when you find stuff that you forgot you have. And your like😁😁
Yeah buddy I can use that. Good times bud👍👍
 
Oh man that's always a fun time. And when you find stuff that you forgot you have. And your like😁😁
Yeah buddy I can use that. Good times bud👍👍
Yeah, I found all kinds of things I forgot I had. Pretty soon I need to focus on getting a storage solution for some of my RC cars. That 42" boat is on the way and I have no idea where I am going to put it 😜
 
Back
Top