Hello all, I recently purchased a LRP ZR.32 For my Savage XL and I heard from multiple sources and even this forum that the carb is notoriously bad at holding a tune.
so what are good alternatives from the stock XTEC carb on these things?
I ALREADY KNOW the NovaR .28 Carb is basically the...
hey guys!
been meaning to start a progress/build thread about this for awhile, but just havent been able to, just a really interesting piece (at least to me) so wanted to keep a detailed log of the project.
for the most part, wanted to keep it as OE as possible, just because of what it is, and...
I have a Savage X 4.6 and I'm putting an LRP 32 engine on it. Having a difficult time finding a muffler made for specifically for this engine. Does anyone have a recommendation for a muffler that is tuned for the LRP 32? I want the best performance I can get.
Well, after fighting and fighting one of my LRP 28S3's, I finally called it quits and ordered a new engine. History of that is here: https://www.rcnitrotalk.com/forum/threads/alternate-carb-for-a-lrp-28-s3.85277/
New engines always look nice when you open the box and this one was no different...
Hey guys... I have an older Savage X... I haven't been able to figure out which engine it actually is. The closest I can figure it's a 4.1 or a very early F4.6. I've really had my eye on the LRP ZR.30 Spec.2 and Z.28R Spec.3. Just wondering what someone else has experienced. With not knowing for...
Ok well I finished my revo Big block quest and just wanted to give info on how i did it....
I used golden horizon upper hitched control arms which give you more than enough space to fit any rotor or pull start using the trx mount !!!! ..I did have to move the Trans forward and also shave a the...
Mook_589
Thread
lrp
nitro engine
nitro fuel
rc body
traxxas
traxxas revo
Just broke in my new lrp .32 and broke the pull start even with the plug open. I had to get a Roto start and I have to heat the motor up to get it running wow this motor is tight!
Hi peps just brought my self an lrp.30 pull start trying to break it in but having some trouble at the moment when i get it started it will idle really high almost like its leaning right out i have turn the hsn and lsn out to richer settings but it wants to take off like its getting full...
Just looking for a little feedback. I recently got back into rc. I picked up a couple used trucks/buggies. Got a nice LST xxl. I decided to put a new motor in. Got a new lrp .28 spec 3. I broke it in as follows: first tank idled up to 205 degrees and let run full tank. Then cooled at bdc. Second...
i bought a new lrp z.28r spec r for my t maxx and I need to know what flywheel clutch and spur set up I should use. I cut the crankshaft off at the end of the threads and I just ordered an Ofna clutch nut part number 10091. I also ordered Ofna hyper 8 motor mounts, I'm quite aware that this will...
Hey guys...I recently bought a lrp z.28 spec 3 for my savage 4.6. I have done a break in..but cannot get her tuned. She seems to be cutting in and out. No power. Then for a brief second she will scream..tHen fall on her face..and running hot as well..went back to factory settings will times...
What do I have to do to make my lrp zr30x fit? It will not fit with the pullstart or the rotostart. It seems that it needs taller engine mounts. The back plate hits the frame before the motor gets to the mounts. Anyone know of a quick simple way to make it work?
Thanks
My poor ol losi 454 in my revo is flat worn out, pricing up the bits to rebuild it properly (piston & sleeve, front & rear bearings) comes out not much short on the cost of a new one.
I'm on a tight budget, I know the losi is a rebadged LRP .28 spec 3 - which in turn is made by SH engines, so I...
Hey guys, hope the title makes sense. Let me clarify..... I have an Ofna Hyper SS that I recently blew the JL .28 motor on. I am hoping that Ofna will warranty, but in the mean time I made the choice to order a JL Z.28R motor. Hard to beat Tower Hobbies at $145.00 with a coupon! Anyways, my...
I just put it in my savage XL and i noticed that the mid range needle was not set to factory and i set it back at 5-25 when I tryed to start it, it started and rev up then shut of i have had it do that 3 times out of 3 diferent times trying to start it. Would that be an idle needle making it...
HELLO, I RESENTLY PURCHASED AN LRP .32 ZR AND DID A 5 TANK RUNNING/STATIC BREAK IN, I ADJUSTED THE NEEDLES GENTLY AND TOOK IT FOR A RUN, THE ENGINE BROKE AFTER THE FIRST TANK DURING A SPRINT, I OPENED IT AND FOUND A THE PISTON CONECTING ROD DISINTEGRATED ON THE PART THAT CONNECTS THE CRANKSHAFT...
My lrp .32 drag modified engine will not get warm for nuttin....got abt 10 tanks thru the hottest i think is like 165F.... If i lean it it cuts out like it too lean....i dont know if its the plug type or gas...i running medium plug and 20% fuel....starting to get pissed I'm usually a good tuner...
It's giveaway time and we think everyone is going to like this power house of a giveaway, a brand new LRP Z.28R Spec 3 nitro engine!
Enter NOW: https://www.rcnitrotalk.com/lrp-z-28r-engine-giveaway/
Be sure to enter daily and @Supporting Member's get an extra 5 points daily entry as well!
Hello, I just purchased an HPI Trophy Truggy as well as an LRP ZR .32. Of course it does not just drop into Trophy Truggy. Can anyone please tell me what mount I need for this engine to go into Trophy Truggy? And where I may order it?
Thanks,
JCruz:thumbs-up: