Want to buy…where to find..

[Cheez ‘n’ Quackers]

Anyone know where I can pick up handles? Modern world problem. Sure changing out the bits is easy enough but I would like to have a couple more just for convenience sake. I tried Tekno and Amain plus a couple of other searches but no luck.

 

[Mtbmatty]

Found These on eBay, it’s a small set, couple of the tools look similar.

You could try reaching out to tekno customer support, they may be able to set you up…

 

[bill_delong]

Amazon sells cheap sets with throw away bits that you can replace easily with quality bits later:
https://www.amazon.com/OFNMY-Driver-Metric-Helicopter-driver/dp/B07FDTQ8LQ

 

[Cheez ‘n’ Quackers]

Amazon sells cheap sets with throw away bits that you can replace easily with quality bits later:
https://www.amazon.com/OFNMY-Driver-Metric-Helicopter-driver/dp/B07FDTQ8LQ

Thanks

 

[WickedFog]

I have had these Dynamite drivers for 7+ years now, and they still look like new. Even with them being used on RC stuff, my 3d printers, and a number of 3d printed projects, they show absolutely no wear at all.
Dynamite Machined Hex Driver Metric Set Red DYN2904 Hand Tools Misc https://a.co/d/3TUequg

 

[DavidB1126]

I have the same set that WF has. I can agree on that. I had that set since 2016 I believe and no wear.

 

[Mtbmatty]

Amazon sells cheap sets with throw away bits that you can replace easily with quality bits later:
https://www.amazon.com/OFNMY-Driver-Metric-Helicopter-driver/dp/B07FDTQ8LQ

I went this route, same exact ones. Only negative was no caps on the ends of the handles. Got a set of nut drivers also ( they have end caps, go figure). pleasantly surprised so far, although I haven’t had them terribly long.

 

[Cheez ‘n’ Quackers]

I have had these Dynamite drivers for 7+ years now, and they still look like new. Even with them being used on RC stuff, my 3d printers, and a number of 3d printed projects, they show absolutely no wear at all.
Dynamite Machined Hex Driver Metric Set Red DYN2904 Hand Tools Misc https://a.co/d/3TUequg

I think everyone is missing the point. I have all that I need. Again, just saying first world problem. Pure laziness of not taking one bit off to put another on.

 

[WickedFog]

Oh, I see. You just need two more handles. Not sure those Tekno tools are even made anymore? So to find a different handle that fits those bit might be a bit challenging, since I'm guessing not many of the sets will list that dimension. Anyway, good luck.

 

[bill_delong]

per the link I posted yesterday, they also sell socket tip handles as well, they might be compatible with the TEKNO bits:

https://www.amazon.com/Drivers-driver-Helicopter-Socket-Screwdrivers/dp/B07G7X1HHD

FWIW.... I only use the 5.5mm and 7.0mm socket bits, never seen any other need for a socket except 17mm which I use to quickly install my wheels with my cordless drill
https://www.amazon.com/gp/product/B07V9HF5Z5

 

[RustyUs]

I think everyone is missing the point. I have all that I need. Again, just saying first world problem. Pure laziness of not taking one bit off to put another on.

Anyone know where I can pick up ^some more of these Tekno^ handles? Modern world problem. Sure changing out the bits is easy enough but I would like to have a couple more just for convenience sake ^and have a complete Tekno matching set^. I tried Tekno and Amain plus a couple of other searches but no luck.

Apparently, the question didn't come across clearly enough on multiple forums. I enjoyed the responses though. Drastic times call for drastic measures. Buy the set on eBay and sell off the non-Tekno pieces, or buy two Tekno XT screwdrivers that are still in stock some places.