-
Welcome to RCTalk! 🚀
Join the #1 RC community where hobbyists connect, share, and get expert advice on RC cars, trucks, boats, drones, and more!
- ✓ Friendly & passionate RC enthusiasts
- ✓ RC tips & troubleshooting
- ✓ Buy, sell & trade RC gear
- ✓ Share builds & upgrades
Post pictures of your LST
- Thread starter LosiLST
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
Thanks for the comments guys sorry that i havent been around yes i will post a write up on sunday i also crashed my muggy a couple of weeks ago so its destroyed
I'm in the process of rebuilding it and i will plastidip the cvd's also. The pics do look akward i took them with my iphone thats why i can't find the charger for my regular cam so the iphone will do 
later romeo
taz1175
Gone - bye bye.
No problem, that's cool....I can't wait to see the pics. BTW, sorry to hear about your muggy !:\:whhooo: BTW, did you do the same thing to your springs on the muggy ?
Last edited:
taz1175
Gone - bye bye.
Last edited by a moderator:
taz1175
Gone - bye bye.
Nice lookin' truck !:thumbup: I like the red Crowd Pleaser 2.0 body on it better than the stock LST body !
Another fine looking silver Crowd Pleaser 2.0 body there TOCCHET ! Nice truck too BTW !
I like the way you have the circle(oval) cut out in the windshield......what did you use to do it ?:shrug: Are you running a Spektrum radio ?......just curious because you have such a short antenna on your truck.- LOSI RULES !
Last edited:
taz1175
Gone - bye bye.
Hey Baggyman, I see you have an Integy roll handle.......I have one on my LST2 as well. So how do you like it ? Have you ever had any problems with it ?:shrug:
https://www.rcnitrotalk.com/forum/attachment.php?attachmentid=7500&d=1238239779
I put a threaded screw through the 2 holes near the top of it to help brace it and make it more durable so that it doesn't bend so easy on a roll over.
It doen't look like that anymore, especially with the Aftershock body on it(it's trashed). I'm running it like a stock looking LST2, with the LST2 body(grey), dish rims(markered blackw/white)/ATX tires and black Losi wing(LOSB8151), but everything else is the same......except that I routed the exhaust under the chassis and out the right side. I'll have to get some pics of it.
So how do you like it ? Have you ever had any problems with it ?:shrug:https://www.rcnitrotalk.com/forum/attachment.php?attachmentid=7500&d=1238239779
I put a threaded screw through the 2 holes near the top of it to help brace it and make it more durable so that it doesn't bend so easy on a roll over.
Last edited by a moderator:
taz1175
Gone - bye bye.
thanks man! i used my trusty dremel to cut all the holes in my lid,i'm runnin' the stock radio set up,i just cut the antenna tube real short.
No problem ! That's cool, so does it still get good reception or do you have any problems with interference ? Did you cut the antenna down too or did you just route it around or down along the antenna tube because I don't see it ? I was just wondering how you did it because I might do the same thing to mine if it works.
I just run the antenna down along the antenna tube and hold it in place with a black cap & 2 rubber holders that came with my orange and yellow antenna's from Dubro.taz1175
Gone - bye bye.
Right on, Thanks.....I really appreciate the pic TOCCHET !:thumbup:
So did you just wrap the antenna itself around the antenna tube and then put a 'cover' over it so that it wouldn't get torn all up ?:shrug:
It was till kinda hard to tell, Sorry !
So did you just wrap the antenna itself around the antenna tube and then put a 'cover' over it so that it wouldn't get torn all up ?:shrug:
It was till kinda hard to tell, Sorry !
taz1175
Gone - bye bye.
"So did you just wrap the antenna itself around the antenna tube", I said that.
That's how I used to do my antennas.
better pic of my antenna.
Thanks for the better pic, the other one was kinda blurry.
That really helps !........But what is that you used at the bottom of the antenna to hold it nice and snug ?:shrug:
Last edited:
taz1175
Gone - bye bye.
a piece of fuel tubing,i put the fuel tubing on the antenna tube first,coil the wire around it then use pliers to pull the fuel tubing over the wire,then i make sure it's all snug and rady to go.
:goodpost: Right on, Thanks.....I really appreciate it !
I never even though about using a peice of fuel tubing, that's a good idea !
Last edited:
taz1175
Gone - bye bye.
Hey Baggyman, I see you have an Integy roll handle.......I have one on my LST2 as well.
So how do you like it ? Have you ever had any problems with it ?:shrug:https://www.rcnitrotalk.com/forum/attachment.php?attachmentid=7500&d=1238239779
I put a threaded screw through the 2 holes near the top of it to help brace it and make it more durable so that it doesn't bend so easy on a roll over.
Last edited by a moderator:
Hi Taz, don't think the roll handle on my truck is integy one. Bought it of ebay some time ago. Had no problems with it, & its save my truck a few time when I've rolled it. Getting some more Fuel this weekend. Will be the first time I've run the new diff covers, heavier oil in my shocks as I was running standard oil with yellow springs, and relocated fuel filter.
