picco .15

[batmanninja]

I got this picco motor from a friend he said the pull start wouldnt work. Come to find out the one way bearing is whats bad. I can not for the life of me find the part # for it anywhere. Anyone know where i can find the part # so my lhs can order it for me? Thanks

 

[tmaxxfreek]

This is the only thing i could find for a ofna pullstart, best thing to do is take the old one with you to the LHS and let them match it up, it may have some numbers on it they can lookup or cross to find the right one.

http://www.ofnawarehouse.com/product_info.php?products_id=803

 

[batmanninja]

Ya the one i need is circular not hex. The mach engines almost have the same one but it has a small bevel n will not fit.

 

[olds97_lss]

Got a photo of the engine and PS? Would assume the .21 version would be too big... http://www.rcplanet.com/ProductDetails.asp?ProductCode=OFN51325

 

[batmanninja]

Thats it but i prolly need for the .15?? I can't(or dont know how) upload pics here cuz I'm using my phone. It sez "picco 15 rc speed" light blue heat sink with black engine body.

 

[olds97_lss]

Have you cleaned the OWB?

I soak them in DA for a few minutes, then wet a paper towel with DA, run the towel through the bearing then spin the bearing on it in both directions. YOu want to twist the towel up so it fits snug inside the bearing, then the bearings will spin/grab it and clean the gunk out if there is any. Then I put a drop of 3-in-1 on it and put it back in the engine.

 

[batmanninja]

No the bearing is actually cracked. Well not the actual bearing but the housing is cracked n it lets the bearing spin in both directions

 

[olds97_lss]

Oh, that sucks. May be hard to find a owb for that engine, from what I could tell it's 6+ years old.

This your engine?
http://www.gravesrc.com/TRINITY_TRAXXAS_PICCO_15_ENGINE_PS_p/tritp123.htm

I wonder if the one from their .06 will fit it...
http://www.nitrohouse.com/One-Way-Bearing-8T_p_8995.html

 

[batmanninja]

Yep thats it or at least looks xzatly like it.

---------- Post added at 6:37 PM ---------- Previous post was at 6:33 PM ----------

Ya that bearing is not it the one u linked for the .21 looks just like it. Mine is circle not hex. Do u think the .21 wood fit?

 

[olds97_lss]

My guess would be no. Would have been nice to find some measurements for that bearing somewhere so you could figure it out. But considering the rotation/size of the crank in a BB would be larger than a typical SB, the owb couldn't be shared between the two.

 

[MessnLosi22]

Picco.15 and Omega X# .26 OWB

No the bearing is actually cracked. Well not the actual bearing but the housing is cracked n it lets the bearing spin in both directions

I have been researching this and found the # by calling Ofna Tech support:

Tech Support / Cust Service: 949-586-2910

Had one helluva time cuz this motor is 10YEARS OLD...lol...
HOPE THIS HAS HELPED!

Mess

---------- Post added at 1:57 PM ---------- Previous post was at 1:51 PM ----------

This is my .26 bearing i need, if you get a part# there are alot of stores w/ Picco parts, similar to Ofna...
http://www.gravesrc.com/OFNA_ONE_WAY_BEARING_p/ofn51325.htm

---------- Post added at 1:58 PM ---------- Previous post was at 1:57 PM ----------

http://www.gravesrc.com/v/vspfiles/photos/OFN51325-2.jpg

---------- Post added at 1:59 PM ---------- Previous post was at 1:58 PM ----------

Pic of 51325..