- Thread starter
- #21
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
just got my yeti motor it was in the mail box
just got my yeti motor it was in the mail box
short course truckYou got a crawler or trail rig?
my truck comes with a 3660 3200 kvshort course truck
short course truck
I've hear they are pretty good and lots of torque. and can handle 4s not that ill run a 4s but my esc is 2-4sAh ,then you are going to use that motor for the SCT.? ,It is a good brand!...
Lol...every time that I see Axial ,I think crawler!...
all said and done... my truck hardly stays on all 4 wheels even with 1:8 wheelsI've hear they are pretty good and lots of torque. and can handle 4s not that ill run a 4s but my esc is 2-4s
I've hear they are pretty good and lots of torque. and can handle 4s not that ill run a 4s but my esc is 2-4s
all said and done... my truck hardly stays on all 4 wheels even with 1:8 wheels
I know you guys think I'm stupid for putting all my aluminum hop-ups on my rig. don't get me wrong, i love my truck. just i like a tight setup my truck goes about 70mph and if it's all over the place u can't go fast. I think my servo has been the prob the whole time. and now it's more noticeable. the only thing i regret is not just getting a 6s sentonarrma should call their 3s lineup 2s. and warn people if they do run 3s that every fkn thing will break. first off they put a 7kg servo in a off road vechle second ...then they put open bearings on something that goes in dirt and water. third they put an esc that overheats in ten mins on 3s. plastic pivot balls don't last a week before they are so loose you can't even drive a straight line. but hey you can launch them 20 feet for 20 mins on YouTube . people buy these thinking they are going to last. bull crap. the only thing stock on my rig is the chassis and gears. and i bet they will be the next thing I change
no i just put the buggy tires on it two days ago. and a new 120amp esc prob solvedI don't think that you ESC should have took a dump on 3's if it says that it can handle up to 4's ,
You say that you run 1/8 tires ,that is buggy tires right?
I don't think that you ESC should have took a dump on 3's if it says that it can handle up to 4's ,
You say that you run 1/8 tires ,that is buggy tires right?
no i just put the buggy tires on it two days ago. and a new 120amp esc prob solved
it blew the Mt tires right off 30minsAh ok ,it must be a beast now!...Have you got to run it ,an how did you like it?
It sounds like ,that you are turning it into a trail/MT truck!
arrma should call their 3s lineup 2s. and warn people if they do run 3s that every fkn thing will break. first off they put a 7kg servo in a off road vechle second ...then they put open bearings on something that goes in dirt and water. third they put an esc that overheats in ten mins on 3s. plastic pivot balls don't last a week before they are so loose you can't even drive a straight line. but hey you can launch them 20 feet for 20 mins on YouTube . people buy these thinking they are going to last. bull crap. the only thing stock on my rig is the chassis and gears. and i bet they will be the next thing I change
ya I've had the same experience. just yesterday. Sat there filing the sharp edoes off so the diff didn't rubI’ve had a nightmare with gears and diffs on my Arrma Senton , they are not all built to the same spec I got a Roses Tub full of New Diff yokes , new Diff Case, Planet Gears, input shafts, out drives , all bought new just have to keep fiddling around to see which best , some planet gears grind for no reason , some diff yokes rub the diff case . Honestly I’ve never known anything like it . However my LCG Slash is wont drive in a straight line either, and don’t even think of driving it without the TSM controller reciver unless your a dab hand at driving on ice because there’s no difference .