Sold / Found OFNA GT Roller

[Plaidfish]

A very used but still working OFNA Ultra GT roller...60 shipped...the outdrives have wear in them but they still keep going....if you rotated the outdrives and shafts around it would last even longer...I just don't feel like restoring another RC.....has badlands wheels...needs tank...the one in pic was rigged on to just bash with it the last day it was used.....

Oh yeah the wing is deadly...I just slapped it together to jump the buggy.....it will cut you so do not go driving this into people thinking it's going to be funny....

 

[Pedester]

Jeez, that would hurt. I never thought of that. Ouch...

What all is worn out?

 

[Plaidfish]

the outdrives and drive shaft pins show wear....but if you were to rotate the cups and shafts you could get some more time out of em...this is really more of a parts car....you'd need a tank, engine mounts, rear chassis brace, engine setup and radio gear....to get it going.....but the gears still hold up well and the it's got OFNA supershocks.......the bearings still roll smooth...and the slop in the suspension isn't bad.....

 

[psunitro]

the outdrives and drive shaft pins show wear....but if you were to rotate the cups and shafts you could get some more time out of em...this is really more of a parts car....you'd need a tank, engine mounts, rear chassis brace, engine setup and radio gear....to get it going.....but the gears still hold up well and the it's got OFNA supershocks.......the bearings still roll smooth...and the slop in the suspension isn't bad.....

Hey Plaid, I want this thing. I'll send you a PM in the AM, maybe we can work out a partial trade.............

 

[ImBroken]

The wing also doubles as a spackle knife...

 

[jon2]

The wing also doubles as a spackle knife...

LOL wasn't that a chop and scoop thing for the kitchen?

Bump for a good guy!

 

[Plaidfish]

LOL...the wing broke last time i WAS bashing and it wouldn't jump right.....so I cut a peice from som stock my pop had laying around his shop.....works good too but it will cut your ankles off......PSU I saw your PM....let me mull it over.....I'm cooking right now

 

[Monkey Wrench]

Any of the parts compatible on a Hyper 7 PCR? Maybe I'll bum some scratch off that good-for-nothing brother of mine if the trade doesn't work out above.

 

[Plaidfish]

that's a tough one...OFNA seems to be hit or miss on compatability.....the gears are probably the same.....the shafts might be.....other than that you might be able to use the whole front / rear a-arms and knuckles/carriers.....

 

[mrwill]

do you take paypal??? if you don't already have an offer I would take it...

 

[Monkey Wrench]

I'm out. If anyone else wants it, Plaid, go with it.

 

[Plaidfish]

deal Pending w/ PSUnitro....

 

[vbgagnon]

whoever buys it I'm pretty sure I have the engine mounts for it.

 

[Plaidfish]

thanks VB...I'm looking for a set in my box now...I don't know what I did w/ em.....

 

[psunitro]

Hey VB, whatya want for em? I have a set but have a scew broke off in them....

 

[vbgagnon]

pay the shipping and they'r yours.

 

[vbgagnon]

PSU nevermind that last post, send me your address and I'll send em. I'm 99% sure the will fit. They are that retarded blue like the chassis of that thing.

 

[psunitro]

Thanks VB. Sent a PM, but I will give ya a couple $$ for shipping, not a problem!

 

[Plaidfish]

Done and gone
Don't see where I can lock or close the thread....

 

[jon2]

closed now!!!