LRP engine in tmaxx 3.3

[Ochana25]

I finally got it. In thanks you helped me out a lot with the pic

 

[Nitro4910]

I forgot to ask you, but do you have bearings in the steering bell cranks or bushings?

If you have bushings you really should replace them with bearings, 4 of 5x8x2.5mm bearings.
http://www.avidrc.com/product/1/bearings/348/5x8x25-Revolution-MR85-RSZ-bearings.html

 

[Ochana25]

Where are those for

 

[Nitro4910]

Where are those for

For the steering bell cranks you just installed, if they have plastic bushings instead of bearings, or if the bearings in there are rough.

 

[Ochana25]

The integy part is installed but there's no servo saver with it

 

[Nitro4910]

What servo are you using?

 

[Ochana25]

Umm I'll be home in 20 min I'll post a pic of it I know it's hi-tech ultra torque

 

[Nitro4910]

Hitec's use a 24 spline output shaft.
Any of the below will work for High Torque MG servo's.

http://www.amain.com/product_info.p...rong-Servo-Saver-Universal-Spline-Connector-1
http://www.amain.com/product_info.p.../OFNA-Heavy-Duty-Servo-Saver-w-CNC-Top-Yellow
http://www.amain.com/product_info.p...9462/n/XRAY-X-Stiff-Composite-Servo-Saver-Set

 

[Ochana25]

This is the servo I got also has a bag with bunch of stuff with it no idea for what lol

 

[Nitro4910]

That will work.

Hitec HS 645MG Specs:
Torque: @ 6.0V:133.3 oz-in
Speed: @ 6.0V:0.20 sec/60°

 

[Ochana25]

So that link you posted I add that directly to the servo

 

[Ochana25]

It seems those to bars going from back to front are just touching the steering linkage making it hard for it to turn I was thinking of grinding the edges a bit to make a clearance what do you think

 

[Nitro4910]

I would put the skid plate on it first, & bolt it down with all the screws & see if it the rubs.
If it still rubs then I would mark the areas with a sharpie that need sanded & pull the chassis braces off to sand them.

The Servo Savers in the links I post bolt down right to the top of the servos output spline.

 

[Ochana25]

So I grinder the edge a bit now it's perfect I went to put the skid plate on and the holes ain't lining up dammit back to the grinder

 

[Nitro4910]

What part are you grinding on?

 

[Ochana25]

Gonna have to grind that back just a tad so the skid plate holes line up

 

[Nitro4910]

That skid is really far off, are the steering posts lining up or are they off too?
The skid should fit without grinding, a small bit of sanding if it's a little bit too tight, but something is off, I have had to do a small amount of sanding
to get some parts to fit well, but that's too far off to be a sand it to fit fitment issue.

Take a few pic's of the front end, top/bottom/ & both sides, for a better look at whats going on.

So that link you posted I add that directly to the servo

Yup, right to the servo output shaft.

 

[Ochana25]

OK will do once I get home from work the skid plate is from a 3.3 maybe it has to be a 2.5 plate and yes it does line up on the steering

 

[hulkmaxx]

4910 is right that's way to far off of a fitment issue man. I haven't been able to get on for awhile looks like it's coming along though.

 

[Ochana25]

Hey hulkmaxx I thought u forgot about my build lol Ya it's weird how it's off I thought. Maybe because it's the 3.3 skid plate