• Welcome to RCTalk! 🚀

    Join the #1 RC community where hobbyists connect, share, and get expert advice on RC cars, trucks, boats, drones, and more!

    • Friendly & passionate RC enthusiasts
    • RC tips & troubleshooting
    • Buy, sell & trade RC gear
    • Share builds & upgrades

Sold / Found FS (2) NTC3s Brand new FT ARR, and a roller

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Status
Not open for further replies.

FastEddy

The Slowest Guy In Town
Supporter
RCTalk Vendor
Messages
14,677
Reaction score
16
Points
730
Location
El Dorado Hills, CA
First is a BRAND NEW built F/T Kit.
(1) Full F/T Kit
(2) Brand New HS-5625 Servos
(1) Brand New Racers Edge Battery Pack
(4) Brand New Foam Tires
(1) Brand New Peak .12 Bench broken heat cycled (5) tanks. (1) tank road test.
(1) Used Motor Saver Air Filter
(1) Brand New Dynamite Fuel filter
(1) Painted and fit body. Stickers are vinyal and on the outside so they can be easily removed.

Just the F/T Kit is 350.00 at tower. Add up the cost of everything else and I have over 600.00 in this car and it has only seen 1 tank on the road and that was to ensure the final break in for the engine that I heat cycled on my Hudy stand. I built this kit fully intending on racing it this upcoming season. I took a great deal of time making sure it was race ready and left no details out. Again, Its RACE READY and has never seen the track. Just add your radio gear and your instantly competitive.

Asking 350.00 This includes shipping in the US
Its the cost of the kit and everything else is FREE.
I also have a roller. Pics and details at the bottom.

ntc31.jpg


ntc32.jpg


ntc33.jpg


ntc34.jpg


ntc35.jpg


ntc36.jpg


ntc37.jpg


ntc38.jpg


ntc39.jpg


ntc310.jpg


ntc311.jpg


ntc312.jpg


The 2nd unit is a roller without an engine. I picked up a great unit and upgraded it with 90% new parts and several F/T upgrades.

New Chassis
New bearing set
New screw kit
New F/T Shocks
New F/T Shaft
New battery pack
New dif kits
80% new suspension graphite parts.

Everything on this roller is ready to race. Just need to add an engine,exhaust, radio and a few odds and ends and your ready to go. For the most part its a F/T 90% new roller.
150.00 including shipping in the US. What you see is what you get.

BOTH UNITS FOR 450.00 Shipped and I will toss in a poop LOAD of extra parts and........ An AE Starter box that is in great shape.


ntc313.jpg


ntc314.jpg


ntc315.jpg


ntc316.jpg


ntc317.jpg


ntc318.jpg


ntc319.jpg
 
Can't get a better deal than this.

Nice job masking the windows off Ed. :green-grin:
 
Need a phone & a flight sim??? lol
Someones gettin a sweet ride...
 
I'm getting a Baja 5B and am cleaning out to make some room.
The only trade I would consider is a New Or Near Mint 5B and I would make up the difference with some extra $$.
 
How much for the workstand? Bump it up for a couple nice rigs.
 
I believe both rigs are sold.
The guy is in PA and says hes snowed in and can't make it to the bank.
Ill give him another day or two.

The stand is for sale. 1000.00 its yours.
you have my PP, and I have your CC# just say the word. :D
 
The stand is for sale. 1000.00 its yours.
you have my PP, and I have your CC# just say the word. :D

You drive a hard bargain but I'll have to pass on this one. :thefinger
 
from what I've been seeing on the news he probably is snowed in......is the stand homemade?.....hella nice rig you sold
 
The stand is all stuff from the Hardware store. I have had it for years now and it keeps on ticking. I have some different lengths of PVC so I can make it taller or shorter. It also swivels.
 
Status
Not open for further replies.
Back
Top