1/10 2wd, and 4wd buggy guys INSIDE!

[CertifiedMike]

I'll have to see if I can get a straight edge across the actual wheel.
This @Littlemotor guy seems like he wants the measurements to be accurate too

 

[jimdavis577]

dang it if you have asked this a few days ago, i had some brand new jc and pl wheels on the bench glueing up some new tires , i can try for some measurement's however as noted ill have to see if i can get the straight edge to sit on the rim to get an accurate measurement

 

[WickedFog]

dang it if you have asked this a few days ago, i had some brand new jc and pl wheels on the bench glueing up some new tires , i can try for some measurement's however as noted ill have to see if i can get the straight edge to sit on the rim to get an accurate measurement

Cut a popsicle stick down. Should be close enough.

 

[Littlemotor]

dang it if you have asked this a few days ago, i had some brand new jc and pl wheels on the bench glueing up some new tires , i can try for some measurement's however as noted ill have to see if i can get the straight edge to sit on the rim to get an accurate measurement

That’s me man-a day late, and a dollar (or 7 ) short! I appreciate ya man!

 

[jimdavis577]

what measurment you want ? from the inside face of the wheel to ??????

 

[Littlemotor]

Overall width from front outer edge to rear outer edge.

Backspace measured from rear outter edge to deepest point of 12mm hex.

“front”space measured from front outer edge to deepest point of axle nut mounting surface.

 

[jimdavis577]

ok here ya go

First off , my straight edge is 15.94 mm ) so 16mm for a round number) This need to be subtracted from all measurements to get the true measurement

so with that out of the way here is from the inside outer edge to the face of the 12mm drive hex

Then the same measurement to the deepest part of the drive hex

and finally the outer face to the face of the wheel nut

 

[jimdavis577]

and these are j concepts 2.2 rear buggy wheels, they are the same wether 2wd or 4wd

 

[Littlemotor]

Thanks sir-have ya already put them up by chance?

I need the width from outside edge to inside edge as well…

 

[CertifiedMike]

These wheels are the same jconcepts

 

[CertifiedMike]

My outside to outside is 1.5"
I will go find a popsicle stick.

I HATE when I have to eat Ice cream for R/C!!!

 

[CertifiedMike]

1.08" to face of the hex to inside wheel edge,
0.215 to the hex face to the outside wheel edge.
DEF a fudge factor on that fudgcicle stick!

 

[WickedFog]

1.08" to face of the hex to inside wheel edge,
0.215 to the hex face to the outside wheel edge.
DEF a fudge factor on that fudgcicle stick!

You gotta go back for another one. Maybe it will be straighter

 

[Littlemotor]

1.08" to face of the hex to inside wheel edge,
0.215 to the hex face to the outside wheel edge.
DEF a fudge factor on that fudgcicle stick!

The only info/measurement I’m lacking is the actual WIDTH of the wheel. The measurement from the outermost face of the front to the outermost face of the back.

@jimdavis already got everything else for me. (No idea why TF it won’t lemme tag him-the forum has been doing weird shiit for me today-maybe it’s on my end..)

No popsicle stick required.

I need the wheel width.

From here:

To here:

Like so:

That’s all I’m lacking…

 

[CertifiedMike]

You gotta go back for another one. Maybe it will be straighter

I tried 2 others and they were no better.
I'm currently trying to straighten a spoon in a gallon of Moosetracks!
I'll find me a straight edge if I have to eat ALL the ice cream!!!
I'm on a mission from Gaaaaad!

1"5 inches wide no popsicle stcks, caliper and Mitutoyo

 

[WickedFog]

My outside to outside is 1.5"
I will go find a popsicle stick.

I HATE when I have to eat Ice cream for R/C!!!

@Littlemotor - this was the first measurement Mike gave

 

[jimdavis577]

38mm outside to outside @Littlemotor

 

[Littlemotor]

38mm outside to outside @Littlemotor

Thanks sir!

 

[Littlemotor]

@Littlemotor - this was the first measurement Mike gave

Sorry bruh-I’ve been wiiiiide open covered up with all kindsa shiit this direction this afternoon, and evening.. whew!

Thanks @CertifiedMike !!

 

[WickedFog]

Sorry bruh-I’ve been wiiiiide open covered up with all kindsa shiit this direction this afternoon, and evening.. whew!

Thanks @CertifiedMike !!

I see you sold your Reds. Time to party?