HPI-Killer
Axial Axle Twisting Guru
Supporter
Okay, I can't keep the fire flaming with nitros right now, always seem to bust something than lose interest.
I am looking for an electric buggy, truggy or a drift car or anything.
Its not FS but if you are wanting to buy, pelase PM me.
I also have a 2.4 ghz TX/RX that will go with either depending on trade.
Also, each rig comes with a glow starter.
First Up: Traxxas Jato 3.3
Build Thread: https://www.rcnitrotalk.com/forum/showthread.php?t=93835
RPM Black A-Arms All Around
RPM Black Front Bumper
New Factory Plastic Sliders
3.3 that was re-sleeved with piston (Needs breaking in)
New Era Truggy Mount
Traxxas Revo Truggy Wing
IMEX Skull tires & black wheels
99% brand new factory Jato lid with custom paint
Traxxas Low RPM Tuned Pipe
Barely Used Factory Traxxas Servo (Steering servo on it is shot)
Converted To Pull Start with ALL EZ Start Crap Included.
------------------------------------------------------
What It Needs
- - - - - - -
Back cover to the tranny (busted ear)
New upper chassis (black plastic one) for the roll bar snapped off the ear that holds her, not really needed if you take the bar off. There is no damage that is affecting the strength of the rig itself.
Next Up: Traxxas Revo 2.5 Fully Converted 3.3
Build Thread: https://www.rcnitrotalk.com/forum/showthread.php?t=94819
RPM Blue A-Arms Up Front
RPM Blue True Track Conversion Rear
Alloy Front Knuckles
Traxxas Red Push Bars
Traxxas Onboard Temp Gauge
3.3 5309 Revo Chassis
MIP Drivelines
Custom Lid (can't remember brand)
Original Traxxas TMAXX Tire/Wheel Combo
FOC (Foward Only Conversion)
Single Steering Servo Instead Of Dual
Converted Pull Start With All EZ Start Crap Included
CRAP TONS of spare parts, springs, arms, too much to list!
This rig was FULLY torn down, cleaned and re-assembled with the 3.3 stuff. After the teardown, I ran it ONE time.
------------------------------------------
What It Needs
- - - - - - -
New Spur Gear And Slipper Kit thats all!
Thanks For Looking.
I am looking for an electric buggy, truggy or a drift car or anything.
Its not FS but if you are wanting to buy, pelase PM me.
I also have a 2.4 ghz TX/RX that will go with either depending on trade.
Also, each rig comes with a glow starter.
First Up: Traxxas Jato 3.3
Build Thread: https://www.rcnitrotalk.com/forum/showthread.php?t=93835
RPM Black A-Arms All Around
RPM Black Front Bumper
New Factory Plastic Sliders
3.3 that was re-sleeved with piston (Needs breaking in)
New Era Truggy Mount
Traxxas Revo Truggy Wing
IMEX Skull tires & black wheels
99% brand new factory Jato lid with custom paint
Traxxas Low RPM Tuned Pipe
Barely Used Factory Traxxas Servo (Steering servo on it is shot)
Converted To Pull Start with ALL EZ Start Crap Included.
------------------------------------------------------
What It Needs
- - - - - - -
Back cover to the tranny (busted ear)
New upper chassis (black plastic one) for the roll bar snapped off the ear that holds her, not really needed if you take the bar off. There is no damage that is affecting the strength of the rig itself.
Next Up: Traxxas Revo 2.5 Fully Converted 3.3
Build Thread: https://www.rcnitrotalk.com/forum/showthread.php?t=94819
RPM Blue A-Arms Up Front
RPM Blue True Track Conversion Rear
Alloy Front Knuckles
Traxxas Red Push Bars
Traxxas Onboard Temp Gauge
3.3 5309 Revo Chassis
MIP Drivelines
Custom Lid (can't remember brand)
Original Traxxas TMAXX Tire/Wheel Combo
FOC (Foward Only Conversion)
Single Steering Servo Instead Of Dual
Converted Pull Start With All EZ Start Crap Included
CRAP TONS of spare parts, springs, arms, too much to list!
This rig was FULLY torn down, cleaned and re-assembled with the 3.3 stuff. After the teardown, I ran it ONE time.
------------------------------------------
What It Needs
- - - - - - -
New Spur Gear And Slipper Kit thats all!
Thanks For Looking.