MudSlinger33
Hardcore RCTalk User
What are you replacing the factory screws with?
-
Welcome to RCTalk! 🚀
Join the #1 RC community where hobbyists connect, share, and get expert advice on RC cars, trucks, boats, drones, and more!
- ✓ Friendly & passionate RC enthusiasts
- ✓ RC tips & troubleshooting
- ✓ Buy, sell & trade RC gear
- ✓ Share builds & upgrades
The Alien13 Flux HP build thread
- Thread starter alien13
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
alien13
Hardcore RCTalk User
- Thread starter
- #43
It's about as done as it's getting for now. I threw a radio in it to test it, after roughing up the body a bit, I think I need to fine tune it a little. I can say that I will be wrecking something, whether it be a passing car, small child, large dog, who knows.
I have more decals ordered, and I still don't know what I want to add to it yet from my own stock, but here's what's done.
I did have to raise the body mounts two holes, and I'll probably go up another hole or two.
Things to do still:
Make skid plate
Make ESC plate for between TVPs
Shim diffs
Install lights
Replace suspension screws
Replace/De-anodize purple parts (If I can find them in red ano I'll be happy.)
Add 17mm hub adapters
Widen stance (Kinda iffy on that, I like the way it looks right now)
And anything else I may think of in the future. This remains to be an ongoing project.
I have more decals ordered, and I still don't know what I want to add to it yet from my own stock, but here's what's done.
I did have to raise the body mounts two holes, and I'll probably go up another hole or two.
Things to do still:
Make skid plate
Make ESC plate for between TVPs
Shim diffs
Install lights
Replace suspension screws
Replace/De-anodize purple parts (If I can find them in red ano I'll be happy.)
Add 17mm hub adapters
Widen stance (Kinda iffy on that, I like the way it looks right now)
And anything else I may think of in the future. This remains to be an ongoing project.
grgbulldog
Hardcore RCTalk User
That looks awesome! I never really thought about putting a SC body on a MT.
Thats nice, the SC body set it off!!
MudSlinger33
Hardcore RCTalk User
Looking good! I would like to see what you plan to use for an esc mount. I also need to make one between the tvp's on my flux xl.
alien13
Hardcore RCTalk User
- Thread starter
- #48
On the TCS XL length TVPs, there is a set of holes just above the rear driveshaft. I pulled the motor plate from a Savage 25 I have sitting in parts. I'm going to use the cross bars from that, and just cut a piece of 1/8 aluminum flat stock from work. Same for the skid plate. TCS sells the stuff, but this shouldn't cost me more than a buck or so for material, and the parts manager will probably give me the stuff for free. We go through enough anyway, it won't really matter.
Agreed :yes:
alien13
Hardcore RCTalk User
- Thread starter
- #50
Tried to shim the diffs today. I hate trying to remove the factory screws. Those are rounded out, but I got them out. Got everything apart, discovered that the shims I have are the wrong ones, so now I sit with a useless Flux. Hopefully tomorrow I can order some new shims and it looks like I need oil too.
Funny how my X4.6 came with a bag of shims, but the Flux didn't. So much for consistency, right?
Funny how my X4.6 came with a bag of shims, but the Flux didn't. So much for consistency, right?
MudSlinger33
Hardcore RCTalk User
What weight diff oil are you using?
alien13
Hardcore RCTalk User
- Thread starter
- #55
Update!!!
Got my shims and oil today, so the diffs are shimmed, 30k in the rear, 50k in the front, with some Mobil Synthetic grease to keep them smooth on the bevel gear.
Now not only is it longer than a Flux HP, it's WIDER too! RC8T 17mm adapters, widened the stance by an inch.
And just to show off:
The truck takes up a good portion of the Cow RC jumbo flat mat.
Still to do:
Make roll cage (I have the material, just need to get ambitious and start it.)
Make skid plate (Need time at work to make it)
Make ESC plate (Need time at work to make it)
Add lights (Thinking about integrating with roll cage)
Got my shims and oil today, so the diffs are shimmed, 30k in the rear, 50k in the front, with some Mobil Synthetic grease to keep them smooth on the bevel gear.
Now not only is it longer than a Flux HP, it's WIDER too! RC8T 17mm adapters, widened the stance by an inch.
And just to show off:
The truck takes up a good portion of the Cow RC jumbo flat mat.
Still to do:
Make roll cage (I have the material, just need to get ambitious and start it.)
Make skid plate (Need time at work to make it)
Make ESC plate (Need time at work to make it)
Add lights (Thinking about integrating with roll cage)
alien13
Hardcore RCTalk User
- Thread starter
- #56
I have the roll cage material, just been to lazy to start it. On vacation for a week, so I might get somewhere. I also cut the plates for the XL skid plate and ESC plate, need to check the fit, and I'm debating on actually bending the skid plate to match the TVP curves.
Great lookin savy 13 great job! And good god that rear diff looks bomb proof!
alien13
Hardcore RCTalk User
- Thread starter
- #59
Mini bash session today in the front yard. Wife wanted to drive her Stampede, so I figured I'd break some poop while she played. After my Sprint 2 Sport broke, I dragged out the big boy, did some jumps off of a makeshift ramp. Took out a tree branch, still landed it and drove away. Did a few flips and the only thing I broke was the hard cases for the batteries!
Thats awesome your wife is taking interest in the hobby, I would give anything for a wife like that, or a gamer wife at that.... Lookin good though man for sure.