Tell us your mods . You no you want to :)

[Jacknifejuv]

I'm a bit nosey and am always curious of how other people have there maxx's set up and what mod's you got and how they run .

---------- Post added at 9:06 PM ---------- Previous post was at 8:49 PM ----------

Heres mine
. Front rpm upper and lower arms ,
Rear rpm arms with true track conversion with oversized bearings .
Front and rear aluminium shock towers .
Front and rear aluminium bulk heads .
Front and rear aluminium skid's with plastic center skid .
4 1/8th truggy shocks on the front 2 on the back with 2 adjustable piggy backs with progressive rate springs .
Forward only conversion . (Love it ) .
2 stage foamy air filter .
Just installed a brand new Trx 3.3 engine in it . Lets see how Long this one last's lol .
Hitec steering and throttle Servo .
Larger fuel tank still not big enough lol .
6 cell hump pack strapped to front .
Custom Wheelie bar .
Resonator pipe .
Oh and a full roll cage wen i want it . Truck is awesome for jumping haven't got to worry about landing it wrong nothing hardly ever break's . Wot runs even over rough terrain is surprising good with the truggy shocks there jacked right up so i have more travel on jumps . With the back end sittin lower than the front so don't have too many front heavy landings.

 

[Rolex]

Tell us your mods . You no you want to

Well, there's NCNitro, Candyman, robmob, Olds, me and maybe someone I missed.

 

[Jacknifejuv]

Each to there own

---------- Post added at 9:24 PM ---------- Previous post was at 9:17 PM ----------

Oh i get ya Lmao i thought ya meant you lot didnt want to lol . We english are a bit slow lol

 

[Lessen]

I knew Ralph would toss in a bit of a different angle on this

My entire truck is aftermarket except for the shafts inside the tranny.
FLM
RPM towers
Flextek susp
RRP gears
custom spurs, brake hex and drive cups courtesy of Racer1966
HB diffs
RB mill
TRX big bore shocks
RCA center drives
MIP outdrives

 

[Jacknifejuv]

Sweet wat she drive/jump like ?

 

[Lessen]

Dunno, never started it.

 

[Jacknifejuv]

Haha your funny .

 

[Rolex]

Dunno, never started it.

Likewise. I have a savage with the stock engine, different cooling head. EVERY other part on the entire truck has been replaced. Never been started.

 

[Mjt63086]

I have a original pro15 tmaxx

RPM Upper and Lower Arms.
RPM Bulkhead Braces
RPM Full Underside Skidplates
RPM Front Bumper
RPM Lightbars
RPM Shocktowers
3.3 Axle Carrier Conversion
Traxxas Performance CVDs for 3.3
Traxxas Progressive Rate Springs
Traxxas Link 2218 2.4ghz Reciever
Traxxas Link 2239 2.4ghz Transmitter
Traxxas 22tooth Clutch Bell
OS .18 CVR-X
MIP Pipe
Motorsaver Airfilter(for hpi savage)
Integy 3 Shoe Clutch
Integy Plastic Slipper Clutch(with metal pegs)
Integy Wheelie Bar
Proline Fuel Tank
Futaba High Torque Steering Servo
Team Associated Fuel Primer
Ofna Fuel Filter

And tons of oem parts I've put on, i know I'm missing some upgrades. Posted this off the top of my head with out looking at the truck, lol.

 

[broken_civic]

castle 1800, mamba max esc, 2 ebay 3 cell 5000 lipo's, wheelie bar with aftermarket wheels I bought from someone on this forum (much thankful by the way, works great) and ubec. I like the way it runs. it's fast, not to fast though.

flysky 2.4ghz radio as well, have no complaints from this radio, hasn't glitched on me yet.

I did have to take it apart shortly after I got it because the throttle quit working and took the throttle piece apart, put it back together, this wasn't the problem. The problem was the connection where that piece plugged into the board. I bent one of the pins and it's worked flawless since. I have another one that hasn't given any issues at all.

 

[rak12]

Well my list is constantly growing, but so far:

RPM arms front and rear (tru trackin the rear)
lundsford hinge pins
RPM 3 piece skids
alum front skid( in conjunction with RPM nylon skid)
Axial 40 series beadlockers with Proline MOAB rubber
Traxxas progressive springs
alum bulks
alum chassis braces
steel center CVDs
fuel filter
17mm splined hubs
Traxxas alum front tie rods
custom mud flaps (front only)
custom shock tower braces
cutom lights front and rear

 

[theant]

Classic Tmaxx 2.5 (4910)

Traxxas 3.3 motor
RPM 3 piece skids
RPM Upper and Lower arms
Traxxas progressive rate springs
FOC
Golden Horizon bulks
Golden Horizon chassis braces
Golden horizon bulk braces
Golden Horizon rear shock tower
Golden horizon motor mount
Golden Horizon steering servo mounts
Resinator pipe
17mm aluminum hubs
Duratrax 1600mah hump pack

 

[Nitro4910]

Started life as a 4910.

4 1/8 ofna shocks
Ofna fuel tank & custom mounts
Aluminum shock towers
3.3 carriers
Traxxas CVDs
3.3 Servo saver
Skyion 144oz MG servo
Aluminum servo mounts & tabs

More when I get some spare coin.

Enjoy the pics!

 

[cdc2711]

I lengthened the chassis on mine by about 3.5 inches and put a going f4.6 engine in it. Put one shock on each corner instead of 2 and put hard springs on them. Put in a high torque metal gear steering servo and took out the reverse in the transmission, made it rear wheel drive with a spool and have really tall gearing in it. I love it, its the most fun thing to drive and I don't what anybody says, it does look a bit of a mess where the chassis was extended but its not for looks its purely functional.

---------- Post added at 6:21 PM ---------- Previous post was at 6:19 PM ----------

I lengthened the chassis on mine by about 3.5 inches and put a going f4.6 engine in it. Put one shock on each corner instead of 2 and put hard springs on them. Put in a high torque metal gear steering servo and took out the reverse in the transmission, made it rear wheel drive with a spool and have really tall gearing in it. I love it, its the most fun thing to drive and I don't what anybody says, it does look a bit of a mess where the chassis was extended but its not for looks its purely functional.

I meant a hpi f4.6 engine, the predictive text did that

 

[granjer]

Just a few for my truck....

Close ratio gear kit
RPM arms
Ported and polished TRX 3.3
Better servos- Hitec 645 HSMG
Removed throttle return spring, installed pen spring.

Thats about it for now.

 

[NitroRC4Life]

Mines bone stock except for a O.S. .18 CV-R

 

[2revo1maxx]

4908/4907 maxx

Picco 26, pull start
Integy 3 shoe clutch
Ths pipe and manifold
Flm bulks
Rpm arms, true track, and towers
Big bore shocks
Ofna tank
Geode wheels
5 cell hump pack
77mm dogbone/revo cups
Front trx cvds
E-maxx be diff in back
Proline '80 chevy
changed entire layout to fit a direct pull throttle linkage.

 

[Snook Man]

1-off custom chassis (5 piece) 3 ½ inches longer and ½ inch wider at the bulk head tabs than a stock short chassis.
New Era 4 point chassis braces
GA 7075 bulks with custom bulk braces
Custom rear chassis brace
Fully captured a-arm hinge pin system
HPI savage 25 diff housing and savage diffs with custom pinion shafts
Custom skids & wear plates
Custom shock towers and body post mounts
UE widetrack a-arms
Custom shocks (Ultra LX one shocks with revo VDP pistons, custom springs and compression limiters)
Custom shock to tower limiter
Revo wing mount with custom attachment bars
Tekno axle carries with custom 8mm stub axles with UE drive cups.
UE cups on the diff outputs and UE dog bones for wheel shafts.
UE cups and Bones for the center shafts
Custom single speed tranny with HPI 1/8th scale CD installed
Custom front and rear brakes with replacable shoes/pads
Ofna steering bellcrank system
Ofna 17mm wheel hexes
Custom Batt/receiver box.
Custom diff housing to chassis braces
Recessed Ofna fuel tank
When finished, it will be powered by an O.S.VG .30 and associated pipe.

And probably a lot I didn’t mention.

 

[theant]

Holy Crap!!!!:bow:Thats a bute!! How many hours and $$$you got into that?

 

[Jacknifejuv]

Serious dollar. Do you use it Lol .