New pipe for maxx

[Childresshunt]

I bought a used 4910 maxx with the 3.3 like a month ago and got it running have done a little work to it but the guy that had it b4 me had got rid of the old plastic pipe and put a crappy rear exhaust on it i bought a traxxas resonator chrome pipe for it and installed it yesterday dont wanna run it right now tho due to cold weather what kinda changes can i expect from the truck I've heard all the duel rear exhaust does is rob power

 

[Zdragon71]

It will run better with the resonator for sure. Quieter too

 

[Mn Monster]

i run Resonator pipes on both my maxx's and they work great ! put a deflector tip on it to help keep the oily residue off your rig !

 

[tmaxxfreek]

+1 on the deflector,that is a must have nothing worse than mud mixed with Nitro,its a PITA to clean!!!

 

[Zdragon71]

I actually still run one on my picco .26 but i drilled out the stinger. In the process now of getting funds in order to get a ERCM big block pipe for it.

 

[Childresshunt]

thats what I've heard and deff what i was hoping to hear but what size deflector does it need a large or medium i have a small one from when i bought one for my firestorm but no way is that going on the resonator stinger way to big

 

[hotrodrob]

How about a bb pipe on the 3.3?

transmited from a mobile communications device

 

[Zdragon71]

The 3.3 needs a small block pipe to run best. The traxxas tuned resonator will do just fine and i used the same deflector off the stock pipe. I just cut the silicone protector off the stinger and it fit fine. Zip tie it on good so it wont fall off though. I'm going with a BB pipe on the picco because its recomended for the .26 max. The small block pipes cause too much back preasure resulting in the carb leaking fuel from around the slide and out of the slide boot and causing a mess. Being that the picco .26 is a mid block mill it is said that they perform best with a bb pipe.

 

[hotrodrob]

Was only curious if anyone hAs tried one,:beer:

transmited from a mobile communications device

 

[hulkmaxx]

That's what I run on my Picco as well runs way better with a BB pipe. As for rear exit pipes, the Slim line pipe works very well at least I like it.

 

[Kyleb]

I'm rocking a ERCM BB pipe BB header on my modded picco

 

[Childresshunt]

i best she screams to

 

[Zdragon71]

Kyleb, that is SWEET!!!!

 

[hulkmaxx]

Very nice my friend!!!

 

[hotrodrob]

I like the raw look too man,nice rig.

transmited from a mobile communications device

 

[Kyleb]

Thx for the compliments. I've thrown on a monoblock chassis extension since then

 

[Ckeithnitro]

Did you get your chassis extension from FLM ?? That's awesome!!

 

[Nitro4910]

Did you get your chassis extension from FLM ?? That's awesome!!

That's a UE MonoBlock Chassis Extension.
http://www.unlimitedengineering.com/cgi-bin/store/13236.html

 

[Ckeithnitro]

Ok found it Unlimited Engineering

---------- Post added at 2:22 AM ---------- Previous post was at 2:10 AM ----------

I have the 2.5 chassis with a 3.3 engine soon to be my .26 red dot will the monoblock extension fit that chassis? It's says there it will hmmm..

---------- Post added at 2:25 AM ---------- Previous post was at 2:22 AM ----------

That's a UE MonoBlock Chassis Extension.
http://www.unlimitedengineering.com/cgi-bin/store/13236.html

The ERCM pipes are wicked aren't they?? I have a few of them I use best pipe!

 

[Nitro4910]

Yup it will bolt up without an issue, I would ask Robin @UE when placing the monoblock order what dog you need.

The Thunder chassis uses a 100mm bone, & a thunder chassis with monoblock uses a 123mm bone if memory serves right.
Maybe Kyleb will measure his monoblock dog bone pin center to pin center for us?

A short chassis maxx w/black trany uses a 70mm bone so the UE 93mm bone should be what you need for a 4910 short chassis w/monoblock.