Need Pics of Your Undercarriage!

[WickedFog]

Hey guys. Me and a couple guys here are working on another cool project, but I need some help. If you could flip your 1/10-1/8 scale RC's over and take some bottom pics with a tape measure stretched the length of the car and another with the tape streched across the width I would be very appreciative.

Here is just a little teaser of a completely adjustable car stand in the works that should hold anything 1/10 to 1/8. Thanks!

 

[Tunedfrog]

I'll go take some right now.
Stampede...

Erevo...

SCX10 platform...

 

[WickedFog]

I kinda need to see the whole length of the RC. Especially the crawlers, because I need to see the spread of the axles. Thanks!

 

[Tunedfrog]

I'll do it again.
Here you go.



You also get the pleasure of seeing the wifes feet...

Erevo

Stampede...

SCX10 platform...

 

[WickedFog]

Thanks again! And tell your wife thank you!

 

[Joe crawler]

Still looking for under carriage pics? I can get you some from BRCC, Mojave,kraton 6s thyphon 6s & couple more arrmas

 

[BuZzLigHtyEAR]

Hey guys. Me and a couple guys here are working on another cool project, but I need some help. If you could flip your 1/10-1/8 scale RC's over and take some bottom pics with a tape measure stretched the length of the car and another with the tape streched across the width I would be very appreciative.

Here is just a little teaser of a completely adjustable car stand in the works that should hold anything 1/10 to 1/8. Thanks!
View attachment 154283
View attachment 154282

This is a great rc workstand https://www.walmart.com/ip/Winsome-...tic-Teal-Walnut-13-4-x-13-4-x-24-2/1505325317
Edit: I don't have this exact barstool, but I have a 24in barstool that walmart sold at some time in the last 5 years.

 

[Joe crawler]

Big Rock

typhon 6s

kraton 6s

infraction 6s

mojave

hope these help

 

[Tunedfrog]

This is a great rc workstand https://www.walmart.com/ip/Winsome-...tic-Teal-Walnut-13-4-x-13-4-x-24-2/1505325317

I really like the stool idea, that would have worked great for Baja I built.

 

[Doom!]

Will try to get some pics tomorrow.

 

[WickedFog]

Thanks guys! Keep 'em coming.

This is a great rc workstand https://www.walmart.com/ip/Winsome-...tic-Teal-Walnut-13-4-x-13-4-x-24-2/1505325317

Not so good for crawlers though

This one will operate like a hydraulic lift carriage does. Completely adjustable for any chassis. The v-block in this pic will rotate, the arms slide in and out and rotate, or you can remove them completely for a flat chassis. It will hold a truck by a solid axle, link bars, or chassis. It will be the ultimate car stand when it's done. Will start a build thread soon.

 

[AlanDewey]

Was going to post photo's of the wife's undercarriage, but she deleted the photos.

 

[Tunedfrog]

Was going to post photo's of the wife's undercarriage, but she deleted the photos.

lol

 

[FJC_GUY]

I'll try to remember to get the Redcat Gen 8, TRX4 Sport, Rustler 4x4, and Vorteks for you this weekend if it doesn't get pushed out of my brain by something else. Although I think the Big Rock and Vorteks should be the same?

 

[WickedFog]

I think I have every RC covered by the design at this point. Our Ryft has a big wheelbase, around 15-1/2", and I can reach past it now. Anything with a 4-link setup, you can also rotate the v-blocks and rest on the links, though the vehicle may slide back and forth without the straps.

 

[FJC_GUY]

I think I have every RC covered by the design at this point. Our Ryft has a big wheelbase, around 15-1/2", and I can reach past it now. Anything with a 4-link setup, you can also rotate the v-blocks and rest on the links, though the vehicle may slide back and forth without the straps.

I fight that right now anyway so not a huge deal. Need a rubber coating on the v-block, something really sticky.

 

[WickedFog]

I will probably dip them in plasti-dip. Looking to add some rubber pads to the top plate as well.

 

[AlanDewey]

lol

No undercarriage, but I snuck this photo of her shock absorbers