My Latest Upgrades

[abadk9420]

Got a few new upgrades for the AX10 as well as another Mod

EEM Delrin Reverse Triangulation Skid
Black Lower bent links
Delrin TCS 4 Link Plates F/R
Delrin TCS Axle saddle pack axle mounts
TCS Lexen electronis mounting plates F/R
Traxxas long links ends
I also did the steering mod off of RCC and installed a hitec 7955 servo for the steering

Here are couple of pics

Before when it was new out of the box

And After all of my new parts and mods to date

and here is what I just did

The bent links really clean up the under carriage IMO

More belly clearence with new bent links in the front

Shot of the new skid

F/R 4 link close up pics

 

[slowngreen]

sure coming along fast Curtis, good job man!!! nothing like new crawler parts lol.

 

[abadk9420]

sure coming along fast Curtis, good job man!!! nothing like new crawler parts lol.

Thanks I am trying to keep up with you, LOL!!!!!

 

[insaneatvs]

looks like i need to get a jump on things to get mine to be better

Great job man

 

[NCNitro]

I would think attaching half a t-maxx to the roof would make it a bit top heavy.












J/K man, it's looking good.

 

[abadk9420]

I would think attaching half a t-maxx to the roof would make it a bit top heavy.












J/K man, it's looking good.

HAHAHAHA funny man I guess it dose kind of look that way in the pic, thats the e maxx in the back ground, it should be back up and running in the next month or so....

Now I just need my DNA Dig....

 

[h8z2luze]

Looks awesome man! Great job.

 

[BMILLER]

Wheres the new chassis lol

 

[abadk9420]

Wheres the new chassis lol

I don't know about a new chassis I am liking this one so far....

I took it out crawling today and it performed quite well, it seemed to side hill pretty good, and the tourqe twist seemed to be reduced a lot...next time I will remember to bring the freaking camera...

 

[omarsez]

question?

can you post links of where you found the parts>> Those look great,, I'm about to make those same mods.

 

[abadk9420]

can you post links of where you found the parts>> Those look great,, I'm about to make those same mods.

Here ya go!!!!
rear 4 link http://www.tcscrawlers.com/On-Sale-...corpion-1-each-US-Patent-Pending-p-16523.html
front 4 link http://www.tcscrawlers.com/On-Sale-...corpion-1-each-US-Patent-Pending-p-16526.html
battery mounts http://www.tcscrawlers.com/TCS-Delr...-for-Axial-AX-10-Scorpion-2-each-p-17203.html
30 degree bent links http://www.tcscrawlers.com/TCS-High...-Pipe-30-deg.-Angle-4-each-Black-p-16931.html
upper link electronics plates http://www.tcscrawlers.com/TCS-Crawlers-AX10-Upper-Link-Plate-Clear-2-each-p-17116.html
they also carry batteries too http://www.tcscrawlers.com/TCS-Craw...corpion-7.2-volt-Deans-Connector-p-16619.html
you can get 7 and 8 cell versions of the same pack if your ESC can handle the voltage...
Rod ends http://www.tcscrawlers.com/Traxxas-Rod-Ends-16-long-4-short-1942-p-16324.html
EEM Double reverse triangulation skid http://www.eastendmachining.com/doretrskde.html

Hope that gets you going in the right direction....

 

[h8z2luze]

you dont order from tcs much do you?

 

[KevinGalusha]

Too bad I dont know anything about crawlers, Or I would know what I was looking at Back to RESEARCH!

 

[abadk9420]

you dont order from tcs much do you?

Who's tcs I have know idea what your talking about, LOL!!!! ya just a little.

Oh and I forgot the MIP C Slpine drive shafts
http://www.tcscrawlers.com/MIP-C-Drive-Spline-Set-for-Axial-AX10-Scorpion-2-each-08101-p-16872.html
and CVD front axles
http://www.tcscrawlers.com/MIP-CVD-...Axial-AX10-Scorpion-4-each-08100-p-16873.html
But Chip Cross tell me that the Axail ones are better,
http://www.tcscrawlers.com/Axial-Ra...iversal-Joint-Set-2-each-AX30464-p-16963.html
but for me the MIP's are better deal at 2 pairs of CVD axles for $38 or one pair of the Axail ones for $28, you only need one pair but it is nice to have back ups just in case....that and I have always had good luck with MIP products....

 

[slowngreen]

those are some great mods Curtis, i actually had my shafty perform the best with the stock chassis too....and tcs ftw!!

 

[BMILLER]

so wheres the vid curtis

 

[abadk9420]

so wheres the vid curtis

I am hoping to go back out this weekend and if I can manage to bbring the fricking camara this time I will take som pics and video, I get to crawling so little that when I do get to go I forget the dam camera because I am just trying to get out the door to go play, LOL!!!!

 

[slowngreen]

what i did with my camera that worked out pretty good was i taped it to the front of my radio lol.

 

[abadk9420]

what i did with my camera that worked out pretty good was i taped it to the front of my radio lol.

That would keep you from forgetting it....

 

[Radron]

That would keep you from forgetting it....

Unless you forget your radio! LOL!!:

Don't ask!! :\LOL!!!