Jeabajuice
RCTalk Addict
Hello. I just received a Team Associated RC10 GT2. I need help with breaking the engine in. Can someone help me.
Thank You.
Thank You.
Last edited:
-
Welcome to RCTalk! 🚀
Join the #1 RC community where hobbyists connect, share, and get expert advice on RC cars, trucks, boats, drones, and more!
- ✓ Friendly & passionate RC enthusiasts
- ✓ RC tips & troubleshooting
- ✓ Buy, sell & trade RC gear
- ✓ Share builds & upgrades
Engine Break In Help
- Thread starter Jeabajuice
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
- Messages
- 5,852
- Reaction score
- 16
- Points
- 703
- Location
- Misawa-shi, Aomori, Japan
- RC Driving Style
- Bashing
- Racing
Give this a shot....
[ame]http://i4.photobucket.com/albums/y116/ImBroken8/breakin.jpg[/ame]
A great link from one of our Mods IMBroken
[ame]http://i4.photobucket.com/albums/y116/ImBroken8/breakin.jpg[/ame]
A great link from one of our Mods IMBroken
Metalhead Matt
RCTalk VIP
Read the heat cycle break in method at the top of the engine forum. Post back after your familiar with that read and we'll take 'er from there. Edit: I bookmarked it Joey! About damn time...
Jeabajuice
RCTalk Addict
- Thread starter
- #4
I got the part where you have to turn the engine on and drive it slow for 2-3 minutes and then let it cool down. Do you have to let the engine idle till it reaches 200 or can you start driving it right away?
Last edited:
Metalhead Matt
RCTalk VIP
Is English not your primary language? There's no way I could explain it any clearer than that write up. That write up is what has to be done.
hi
hi
Rc 10gt?not sure but the engine i think its .15 or .18,now in that case i always use a 15% nitro.
THINGS YOU NEEDED:A FULLY CHARGE IGNITER,SCREW DRIVER AND THE NITRO,WORK STAND or mini toolbox FOR THE UNIT.install the battery
for the receiver and trasmitter.
FIRST STEP
ut nitro in the fuel tank...but not too much full
SECOND STEPut ur car in the work stand or center stand and make sure
that the tire is on hanging and never attach on the ground.
3RD STEP: let the gas flow into the curve by pulling the pulstart one or more
until u can see the gas flow and end to the curve.make sure not
too much to avoid gas overflow.
4RTH:hold the igniter and try to snap on top of the head of the engine w/c is
the glowlug s located.
5th STEP: while the igniter hit the gowplug pull the pullstarter and manually
adjust the idling needle a little bit clockwise from 12ocklock to 1
ocklock.
6th STEP:if the engine is working already dnt let stop until 5tanks or if ever
dnt worry it doesn't matter.restart it again.
7th STEP:after 5 tanks let it cool for 10mins. and start it again
in this stage you can run it on the ground.
8th STEP:start to adjust the speed of your car by turning the high end
neddle using screw driver, if u want it fast? turn it clockwise if you
want slow counter clockwise. but be careful of too much speed
might broke your engine.if u have temp gun.for that engine 220
fareignheit is better temperature.
BUT FIRST BEFORE YOU RUN IT CHECK THE BATTERY IF ITS WORKING AND BE SURE THE ANTENNA TUBE IS ATTACHED WITH RECEIVER CABLE.OPEN THE RECEIVER BOX AND U CAN SEE THE RECEIVER.
I KNOW THIS IS NOT A PROFESSIONAL SOP OF BREAK IN BUT I USED THIS PROCEDURE FOR ALMOST TEN YEARS AND I NEVER BROKE AN ENGINE EVER SINCE.
HOPE THIS CAN HELP YOU DUDEEEEE............
MORE POWER TO RC HOBBY............
sorry I'm malaysian
hi
Rc 10gt?not sure but the engine i think its .15 or .18,now in that case i always use a 15% nitro.
THINGS YOU NEEDED:A FULLY CHARGE IGNITER,SCREW DRIVER AND THE NITRO,WORK STAND or mini toolbox FOR THE UNIT.install the battery
for the receiver and trasmitter.
FIRST STEP
ut nitro in the fuel tank...but not too much fullSECOND STEP
ut ur car in the work stand or center stand and make sure that the tire is on hanging and never attach on the ground.
3RD STEP: let the gas flow into the curve by pulling the pulstart one or more
until u can see the gas flow and end to the curve.make sure not
too much to avoid gas overflow.
4RTH:hold the igniter and try to snap on top of the head of the engine w/c is
the glowlug s located.
5th STEP: while the igniter hit the gowplug pull the pullstarter and manually
adjust the idling needle a little bit clockwise from 12ocklock to 1
ocklock.
6th STEP:if the engine is working already dnt let stop until 5tanks or if ever
dnt worry it doesn't matter.restart it again.
7th STEP:after 5 tanks let it cool for 10mins. and start it again
in this stage you can run it on the ground.
8th STEP:start to adjust the speed of your car by turning the high end
neddle using screw driver, if u want it fast? turn it clockwise if you
want slow counter clockwise. but be careful of too much speed
might broke your engine.if u have temp gun.for that engine 220
fareignheit is better temperature.
BUT FIRST BEFORE YOU RUN IT CHECK THE BATTERY IF ITS WORKING AND BE SURE THE ANTENNA TUBE IS ATTACHED WITH RECEIVER CABLE.OPEN THE RECEIVER BOX AND U CAN SEE THE RECEIVER.
I KNOW THIS IS NOT A PROFESSIONAL SOP OF BREAK IN BUT I USED THIS PROCEDURE FOR ALMOST TEN YEARS AND I NEVER BROKE AN ENGINE EVER SINCE.
HOPE THIS CAN HELP YOU DUDEEEEE............
MORE POWER TO RC HOBBY............
sorry I'm malaysian
