Had nothing better to do, so....

[Çh®i§tiªñ]

Here is my entire NitroTC3 setup without transmitter and starter box (because I use them for other cars/trucks as well)

Team Associated - http://www.teamassociated.com/

Kit - NTC3 Kit, non pull, rear exhaust start - #2031 - 459.00
http://www.teamassociated.com/shusting/CatalogHub/kitspecs_ntc3/kitntc3-top.jpg


HardCore Racing Upgrades - http://www.racinghardcore.com

Upper Deck - Ti - HCR-02511 - 60.00
http://www.racinghardcore.com/product/asc/ntc3/0251/blue.jpg

Brake Block Input Cup - T6 - HCR-02521 - 35.00
http://www.racinghardcore.com/product/asc/ntc3/0252/blue.jpg

Input Cup - T6 - HCR-02571 - 21.00
http://www.racinghardcore.com/product/asc/ntc3/0257/blue.jpg

2 Speed Center Bulkhead - T6 - HCR-02581 - 34.00
http://www.racinghardcore.com/product/asc/ntc3/0258/blue.jpg

Drive Shaft - T6 - HCR-02541 - 32.00
http://www.racinghardcore.com/product/asc/ntc3/0254/blue.jpg


RPM Product Upgrades - http://www.rpmrcproducts.com/

Impact-Absorbing Front Bumper - 80272 - 10.95
http://www.rpmrcproducts.com/products/assoc/pics/hires/80275.jpg


NOVAK - http://www.teamnovak.com

XXTra 75mHz Synthesized FM RX - NOV2675 - 104.99
http://www.shopatron.com/img/product_images/NOV2675.jpg


Futaba - http://www.futaba-rc.com/

(2) S3003 Standard servos - FUTM0031 - 11.99 ea.
http://www2.gpmd.com/image/f/futm0031.jpg


EMS - http://www.emsjomar.com/

SANYO - 5-cell Receiver Pack 6v 1100mah - 5KR-1100AAU - 17.95


Mugen Seiki - http://www.mugenseiki.com/

MT .12 BigHead RE - 189.00
http://www.atomichobbies.com/mugenpic1.jpg


HPI Racing - http://www.hpiracing.com/

HPI Lotus Elise Sport 200mm Body - 7433 - 24.00
http://www.hpiracing.com/graphics/bodies/7433.jpg

HPI Rounded Foam Tire Inserts 26mm - 10.00 (all 4)
http://www.hpiracing.com/graphics/tires/tcpmifr.jpg


FUN WOW!

-Chris

 

[FastEddy]

I want a photo of your car not links.
Is it still in a bucket like your Maxx?

 

[Çh®i§tiªñ]

Heheheh NOPE! Its done.

I just picked up all the Harcore Stuff yesterday. With the exception of the Ti upper deck, none of the hardcore has been installed. Thats the project this weekend.

Ill post some pics tonight.

Still at work

 

[Zoomer]

Where are the pics. i wanta see it has been awhile, I have a NTC3 RTR, what motor would you recommend me changing mine too?

 

[Çh®i§tiªñ]

Ill have to get some new pics up tomorrow....

Havent been able to run this kit yet. Built it, then it snowed. I refuse to run this car in the extreme cold. Too much invested.

As far as getting a good mill, well, I have seen them run with the Mugen Seiki MT .12 BigHead and can only say WOW! FAST! and runs cooler than others.

Can you run bump start on yours for a starter box? No idea. Does you chassis have the cutout on the chassis for the flywheel? Can you see the whole flywheel from under the car? Pics?

2 speed is definately what gets it the top end otherwise not seen. I went with the Team kit and built it from the ground up. Forward only, 2 speed, 4 wheel drive, bump start and rear exhaust.

 

[RaCinJason399]

cool sounds sweet now you can go race those retards at the eastern hills mall on sundays. retards because they crashed into my buggy cus i was beating them so they took me out. and snow sucks for on road cars dont it?

 

[Zoomer]

Yeah the cut out for the fly wheel is there, but I was wondering if having the pull starter still on there will have anything to do with it not working?

 

[Çh®i§tiªñ]

Well if you are getting the new MT .12 you wont have a pull start so that should be fine.

You should just be able to remove the pullstart, put the backplate for that mill on, and use the bump start method. What mill?

-Chris

 

[Zoomer]

This here is all I can get
High Performance .12 size ABC pullstart engine
it if from Team Associated, and it came in the RTR kit.