Hi, all! i'm new to the nitro rc hobby, and i'm having a problem. I got a redcat shockwave for Christmas last year, than I used it for about 1 month, than it broke, I never got around to fixing it until 4 months later. I fixed the engine, got it running, and replaced the battares. now when I...
Hi all.
I'm new to the hobby. My model is a Kyosho DBX 2.0 which I got as a gift.
Last year I asked a question on the forums about a broken throttle servo horn, which I replaced after getting the parts, with the right part number in my manual.
After fixing this, I took the car for a spin and...
I've had my t maxx for about 3 weeks now and just over the last 2-3 days I've heard my throttle servo make alot of noise. It is shaking and kind of spazzing on it own. Any idea of what could be causing it to do that? could it really have been messed up that easy?
Hello,
I have had my Trophy 3.5 for a couple of weeks now and it's started playing up (throttle is sticking and it is chucking out lots of blue smoke even though i've got it at it's optimum HSN and LSN settings).
So, first off i would like help on what the throttle problem is. I was out...
Hi i have bought a brand new Nitro rc buggy and iam a total novice to these.
I have no problem starting the engine though as soon as it starts the engine starts full throttle. I have read that i must adjust the idle control screw so that the gap is around 1mm. I have tryed this and this has no...
I recently bought the Duratrax 835b and I did the break-in process and it was all fine and dandy. Then, both my servos went out, so I got two Hitec servos to replace those. When I started it up again it went at full throttle. I reset the throttle linkages and the same thing happend. I...
Hey guys, I recently bought a Thunder Tiger EB4 S3 1/8th nitro off-road buggy. Went through the break-in process. Now working on getting better tuning.
Anyhow, If I'm running it at high speeds and release the throttle all together (or hit the brakes) the engine dies. It seems to idle fine...
what are the proper procedures for adjusting the sevo throttle /brake rods on my 3.3 tmaxx. I installed new gears in transmission of course removing the linkages nwo i dont have something right because my engine is flooded with fuel and will not start i removed the glow plug and spun it over and...
Hi guys l have a savage x k4.6 the problem is that every time I press the brake pushes the throttle inside . (when I hit the brake it closes the carb.)
I try to reposition the servo horn, I also cut a little servo saver spring the one underneath the servo horn but I still have the same problem...
Ok put the glow plug out of revo in the redcat volcano.
best that truck has ran yet, well for 5 min until throttle stopped.
the servo has stopped working, what can I replace it with that is cheap?
guy supposed to buy it Thursday so I need it goin.
ok i will warm the engine up by doing a few laps around the track not runing her hard just to make her happy and then when she all warmed up i give her full throttle and takes off like a bullet and then more to the much higher rppms it will start to loose poer and bog and if you keep the throtle...
Hello, yesterday was driving my slayer and noticed the throttle servo would not open full throttle. What's very odd is when the engine is off it opens no problem but when its running it starts to trip out and not go full throttle. But by hand I can fully rev it and its fine. Could it be the...
hey guys, I'm new to nitro rcs and was wondering if it is normal for when i get it tuned for me to press the throttle for there to be a a delay before it actually start going? thanks guys
Hi All,
I've got an interesting problem with my 3.3 which has plagued me for a week or so now - had the car about 6 weeks and bashed it pretty hard :D. Basically when driving, the throttle cuts out and the car doesn't respond to the throttle for a second or two then it starts again. I was...
The factory servo horn is poopy for breaking. Can you guy help out with a good upgrade for the throttle brake linkage? I searched it & found ofna upgrades but part #s were no good. Thanks for the help.
Hi Guys,
As some of you may be aware, i had to buy another throttle servo as the cables on my old one detached themselves from the actual circuit board.
The new servo ( GS-5509MG Go Tech ) has started glitching/juddering under load usually but it does do it with the servo arm detached...
Hi guys newby here ,, I installed me picco on the revo with ofna mount ,, now I'm having issues with the throttle I haven't even broken it in yet but I can't get the carb to open fully ,, I guess weak servo or maybe the spring is to strong for it or mount its just not perfect ,, the problem I...