servo

Old batteries in the cars servo area.. maybe that's the issue. But the car still worked after hammering it threw the parking lot and then when I pushed the brakes when I approached it it appeared to stop so I pinched the fuel line.

specifically, what kills them. By reading posts, I see that servos do die, and that the original HPI servos may not be the best. I have a few dead servos laying around, no gear issues, all electronic related. What is it that dies in the servo, what causes it, and is it repairable? I have a...

Hi guys, I'm almost at the end of a Savage XL rebuild, however my steering servo seems to be, well, I don't know, broken, possibly, possibly not... The main issue is that when the wheels turn left or right, they don't completely return to the neutral position, and the servo seems very sluggish...

Tmaxx classic. Throttle and shift servos are super sluggish until they cycle a few times (like they have to warm up?). Once they'be been cycled a few times they seem to operate at a normal speed. This rig was sitting on a garage shelf for at least two years, if not longer before it was given...

Picked up a nitro rc someone was throwing out, and i want to get it running again. I have close to no knowledge with nitro rc cars although i do i work with motorcycles so i understand the basics of the motor. i know it is a traxxas but not sure of the model. any answers would help a lot. Also...

Hi folks, firstly I've looked at the page on servos but was getting a bit confused, what's the best steering servo upgrade for the thunder tiger S50/mgt 8.0, looking for a more responsive servo, the one that's on it seems to struggle a bit,

Hello to all , I'm new here , and first off all sorry my bad english I'm portuguese.today i complete the break in and the tuning of the engine , so finaly i put body and start the happy for short time , my steering servo locked tho the right and can't move them.they are locked with car turn on and...

okay putting together xmt racing's monster truck ...I had to replace second steering servo, it was one of the parts missing. I also had to replace receiver, manual says 3 channels, but I have 2 steering servo, throttle, and power from battery... so how do you put 4 wires into a receiver with 3...

After I crank the truck, I can throttle the control, and everything works fine. The problem I'm having is, the brakes don't seem to work at all and when I try to apply the brakes, it's almost like it bouncing that servo motor from brake to throttle and it gets stuck. I have no control of...

I've been lurking for about a month since I got my Savage X 4.6. I have already got quite a few hop-ups and up graded both servo's. I am running a Hitec 7955TG for my steering and a Hitec 5565 for my throttle. I have only ran about half a gallon through it so far. It has broken in well and I...

Ok I have a new duratrax 835B nitro 1/8 scale buggy, I just got it back from the manufacturer and they replaced the carb under warranty. I took it out yesterday and bashed around with it for a good 2 hours. Ran great the entire time and tuned it a little bit, I got up today and took it out and I...

Hey everyone so my throttle servo decided to pooch out on my frankenmax it was a spektrum one wondering a good recommended servo

After few nightmare day of trying tune the engine(with no luck) I think there is something wrong with my throttle. As you can see on the video the servo is making strange noise and its not opening the carb full. I can push it and open it full with my finger but the servo wont do that. Is the...

I've been thinking about upgrading from double A's in my receivers to using rechargeable and found some massively discounted rx lipo packs on amazon. I would be mainly looking at using it in my Traxxas Slayer Pro and i was wondering if the stock 2075 and 2056 servos can handle the 7.4 volts...

I am looking to pick up the xtreme racing cf throttle mount kit. I have a new revo 3.3, and wanted to make sure this mount kit works with the stock mounting holes, to me going by the photo only it does not look like it would be wide enough to match up with the holes in the chassis. Also where...

Ok, well i just recently installed a hitech Servo HS-5645MG and had to replace the switch and went ahead and got the hump pack. (BTW huge difference in torque with the hump pack) When i was testing it i noticed that the left wheel was turning more than the right and when turning to the left the...

i would like to use the above mentioned servo but have a few questions. Which servo horn do i need to use that is compatible, with this servo. Are there any other alum arms that will work since i can't find the proline one anywhere? I already purchased the heavy duty spring.

first off its a team associated mgt 8.0 Monster truck. I just bought it used and when you turn it on the servos twitch that's all it will do. You can easily move them by hand and they do not return to original position. The transmitter does not effect it at all. By the way I'm new to rc's this...

i have ordered a set of mg servos that come with a bunch of o rings small screws and different types and lenghts of armsthe steering servo is what I'm having trouble with i have a smartech winner one. 1/10th scale. the steering servo is upside down mounted. and i dont know how to assemble the...

i have a question i was playing in the snow with my car n my steering Wheel started goign awire litterly went every directions none stop. so i stoped the car and ill let it dry n test it again... but my question is how can i water proof the servos and the reciever ??? i saw ppl on YouTube doing...