I am a big Kyosho fan and I have recently acquired the MP10T and finished to convert it to Brushless/Electric.
Even though the conversion process is quite smooth and easy there are a few little things that are good to be aware of before starting.
I have made a short tutorial...
Hey there! First post here. I recently purchased a 1/5 FS Racing petrol buggy along with a tuned exhaust upgrade (which I had no trouble installing) and a 4WD conversion kit. (of which I haven't installed yet) However I am not very mechanically minded on what needs to be disassembled and...
So I seen a few brushless mgts here and have watched a bunch of videos.
Has anyone done it and what exactly do I need? I’m thinking of doing one. I def prefer to do it like a 1/8 scale buggy diff and get rid of the trans.
I’m new to this forum but I want to start off a conversation for a build that I have in mind. I’m looking to build a T-Maxx with the LRP .32 Spec 4 with the X-Tec carb (Already have brand new). I want to run a ERCM pipe because I have heard nothing but good comments on Robin’s work...
The new Tekno ET410 Truggy shares about 95% of the same parts as the Tekno EB410 Buggy. This makes converting an EB410 into a ET410 truggy pretty easy. Below are the list of parts you'll need to make the conversion happen.
Parts needed to convert a Tekno EB410 into a Tekno ET410 truggy
Sorry to bother everyone again. I really wanted to convert a truggy to a buggy. It's and ftx carnage NT. Can anyone tell me how to do it? Thanks for all your help. This is the best forum I have been too.
What does it take to convert an 8ight-e 2.0 buggy to a 4.0. I recently tried purchasing 2.0 a arms and found out they are discontinued. I was able to find a pair of front arms on eBay but that's just a temporary fix. Will 4.0 arms and hubs match up with the 2.0 chassis and diffs?
Hey, hello. I have my losi 8ight 1.0 to be converted into electric. I have been looking around and can't seem to find a conversion kit for it other than the rc product design, which I can't seem to find anywhere. And I don't want to waste money on a tekno conversion kit.
I currently have the car...
Hiya Guys :) . I know it's been awhile but for the last several years I put my ground vehicles on the back burner and focused mainly on my fast electric offshore boats instead. The rc boating around here has come to a standstill and I got tired of running by myself so I let them go and picked...
So....I'm planning to swap a brushless into my Jato and I need to figure a couple things out.
Single speed done
Already have a motor mount planned
3s or 4s lipo
Hobbywing EZrun 2200kv or Hobbywing 3400kv (combos with esc)
I've been told Revo spurs will fit the Jato...is that all...
Losi 8ight conversion by fragged3d posted Jun 27, 2016 at 9:29 PMLosi 8ight conversion 2 by fragged3d posted Jun 27, 2016 at 9:29 PMLosi 8ight conversion 3 by fragged3d posted Jun 27, 2016 at 9:30 PM
How much would you pay for this, no transmitter or receiver!
Ok so the only way I can get my 3.3 to start and idle is for it to be at half throttle. I myself have been over it numerous times as well as the hobby shops, and can't figure it out. Brend new everything except piston and sleeve,because they were still in good repair,new carb,tank,lines. Lots of...
This has probably been asked a number of times for various cars. I was wondering if all I'd need to convert a brushed motor electric car to brushless would be the motor and ESC?
I have the following cars and I'm undecided which to try this on but since my NiCad batteries are shot I thought I...
I bought a t maxx that was what looks like to be in the middle of a 2.5 to 3.3 conversion. It already had a lot of 3.3 parts like the motor all the a arms and basically everything besides the frame, transmission, and driveline like the differentials. The 2.5 transmission messed up so I bought a...
I have a dbxl but after i bought the dbxl i did not know that losi made an MTXL. i want to put monster truck tires on the dbxl just cuz i wanted a monster truck from the beginning , but didnt want to get a redcat because of all the bad things I've heard, can someone help me or refer me to a site...
so i just managed to snag a dynamite .31 gas/petrol engine
i'm going to see if i can fit it into my savage,
a few questions, before i get started
1 - could i keep the stock fuel tank and just change the lines since it uses a rubber o'ring seal?
if not could someone recommend a...
Axial has just released a 2-speed Hi/Lo Transmission conversion kit for the 1/10th scale Axial Yeti. The Yeti 2-speed Hi/Lo Transmission kit comes with everything needed to complete the conversion, including a second taller high gear and all gears are heat treated for ultra durability. The only...