carburetor

Hey guys I have got a XTM Terminator 24 engine. It's almost been a year since it was turned on. For the last couple of days I tried starting it up but its useless. Priming works, fuel goes through the pipe but it doesn't seem to go through the engine. Now i gave up. Please could you give me a...

So I stripped the fuel inlet on my carb on a trx 3.3 for a tmaxx classic. I know I can get the carb body at my lhs for $16 since the components are still good. My question is is it worth it to just get a diff carb altogether or.just stick with stock? I've heard of traxxas carbs having vapor lock...

I am beginning to suspect that I have damaged my carburetor in my Stampede. One day while making adjustments to the carburetor I think I might have turned the LSN too far clockwise. I have no fuel (coming in the mail!) so I can't try anything right now but yesterday I went to put the carb back to...

I have taken my TRX 3.3 engine apart in order to clean it. After having it put together I did a test to detect air leak using a soapy solution. Unfortunately, the front bearing has a leak, but I've also discovered a leak at the carburetor slide and the dust boot, as bubbles formed between the...

Hi, I am in the process of sealing my engine and I am unable to get my carburetor back on. I don't think it's being held up by the locking pin but I guess I'm not sure. Should it take a lot of force to push it back on? It seems like its getting hung up before even reaching the locking pin. I've...

Now I'm a NOOB to nitro so bear with me. I JUST bought a tmaxx 2.5 about a week ago (nib). Broke the engine in per traxxas. I tunned the HSN, thenwent for the LSN and then idle. My carburetor slide (5233) to carburetor body (5234) doesn't really slide. After i took it apart and cleaned...

hi there, I'm a beginner and i don't really understand how to tune a carburetor could someone explain that to me please and if there is anything else i should know about nitro rc cars please lat me know. THANKS

Self proclaimed new to nitro guy here... Got a used Maxx 2.5 converted back around xmas and spent a few weeks doing a tear down, clean and rebuild. Been ready to fire it up for weeks now but the deep snow and cold temps here in Iowa have kept me looking at it sit in a corner. Yesterday being...

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=230381913124

I've been trying to get this "pinch bolt" as the internet says to take out, and it should twist right out. Well, I can't get the pinch bolt. It's not a screw like the example engines I've seen, so I can't just twist it out. (At least I don't think" and I tried putting a screw driver over it and...

So I've had this t-maxx since about 04 of december, and i've had it stored up for a year, maybe 2, and i decided to take it out, fix it up, and get it running again. I've fixed most problems until I came to this one. I was driving it around and it shut off on me, so I went to check it out, and...

can anyone tell me how to set and ehat the different between High-Speed Needle and Low-Speed Needle? how about the factory setting, i mean how many turn from closed of the High-Speed Needle? thanks

I have just fitted a Sportwerks Turmoil .26/.21 Carburetor on my Mach427 in the LST2 With this carb the settings seem a lot more sensative than on the one that came with the Mach427. I though tuning would be easy with this carb, after reading good reviews of it. I have the 9mm insert...

I love my revo 3.3 so much and like to run it a lot. Last night during after run procedures, I was spraying WD-40 into the carburetor. It opened with ease and i sprayed it in... I didn't think i put enough in so i figured id open it up again and spray more. The carburetor would not open! Now...

Does anyone have a rotorary carburetor for a generic .18 engine. Not looking for anything awesome but I figure theres plenty of you guys with blown out .18 engines with working carburetor. Just trying to find something to hold me over untill i can save up for an OS so i'm looking...

Hey, I need a carburetor for my MGT .21, preferably new or slightly used/like new, not heavily used. Thought I would try to give someone on RCNT some business before I hit up eBay.

It opens this far (see image below), but without help it won't go any further. I ripped it apart and discovered this little chip in it, no idea how it got there. Am I going to need an entirely new carb, or just a valve assembly kit? I have no idea if the inside of the carb cylinder walls...

I'm in need of a carb for a hotbodies .26 engine. ether a hot bodies carb or one that will DEFINATLY work in its place. thanks guys.

I have a Hyper .21 8-port engine I've had some trouble tuning. It seems to constantly overheat in high rpm's. I'm familiar with the tuning process so please don't tell me I'm running too lean, cuz I'm not :) Anyway I started searching the net about articles that could help, and found that...

Up for grabs is a brand new in the package HPI part #1666 complete carburetor (SS). This carburetor is an awesome upgrade for the NitroStar 15 FE Motor. HPI says, "If you want to give your 15FE awesome speed you really need a new carb. Always get a replacement with two settings (low speed...