I snapped the frame of my 1/16th slash off where the rear bulkheads attach, so I'm thinking about making a more "scale" 1/16th slash with a solid rear axle with a roll cage and rear solid axle.
I just can't find a 1/16th axle anywhere. Anybody have any suggestions?
Hello guys. i have found out that my front axles have work away at the cup bit where the dog bone fits in, this is causing me lots of problems. i need to replace the axles but i can't find what I'm after.
I upgraded to 17mm hexs and when i did this i had a differnt axle to the originals. i...
I am new to this as you know. I got AX10 Scorpion rock crawler RTC 4WD drive, took it down to the Desert and it was doing great, climbing and really showing off!! Then it won't climb a small log that it had done just a few minutes before. I picked it up and the front drive axle had come off the...
First of all, how do you set the toe and make sure they are both aligned properly without a gauge?
Second, pushed all the way down, the cv pins just hang at the edge of the diffs, will these pop out?
Just finished installing my new pivot ball steering conversion, and before I run it I...
I have a feeling i will end up replacing the Tru-Tracks i have right now, I'm not gonna trust the cross threaded retainer to stay put over the pillow ball. So i will be switching over to either standard RPM arms or maybe the Extended wheelbase Traxxas arms, now my question. Are the Tekno Rc Revo...
I want to put a RPM tru-trac kit and a-arms on my older maxx, but I was told that I'd have to use 3.3 axles and front turnbuckles/knuckles in order to do this. Is that true? I don't mind either way, I'm just going to start slowly collecting parts to make this happen, so I want to make sure that...
This is getting ridiculous, I just broke my 5th axle carrier on my mini-revo. This time it was actually a friend I let operate, but the hits were not all that hard. It looks like all the aluminum options are currently sold out, but man the Traxxas stock carriers are bogus!:angry:
Traijin
Just as the title asks, wondering if anyone here has been running the 30deg. caster blocks up front, and what are your results and in what conditions?
Good or bad mod in your experience?
Same goes for the inline axle steering knuckles. I'm a bit skeptical of those, but simply curious if...
Looking to get complete front and rear axles for this rig. I don't care how beatup they are, as long as the housing isn't cracked and the diff or bevel gears aren't missing teeth, I'll buy them.
Thanks
So I replaced my axle carriers with RPM's about a week ago and got about an hour of runtime on them in a dirt pit and when I came in to shut it down it sounded like their was tons of sand stuck between the axle and the carrier well I took it apart and it wasn't all that dirty so I removed the...
Here's some interesting pics. Have caused some discussion on the UK scene, anyone here got any thoughts?
I'm not convinced. For all the clearance you gain in the centres the motor mounting will make the upper links awkward to mount and also raise the CoG a lot compared to a Bully...
Come with high steer knuckles which are also available separately.
http://www.axialracing.com/ftp/ax30533_behind-the-axle_bta.html
Boo for not being setup for a 4-link and not having some slots cut for a velcro battery strap.
I've been thinking about it for a long time now and finally decided to do it today.
Using a Ultimate berg clocker from a member on rcc.
Going 30 degrees on the rear axle and 20 on the front.
heres the rear.
Unclocked axle and fixture
Fixture in place, with my mismatched...
My stock 5309 axle carriers are due for replacement finally. I was looking at the RPMs with the oversize bearings, or maybe the PE setup. Anyone have advice, or a setup that has worked out well?
if you are interested in them and want pics i can get em, just let me know.
set of used axial axles front has aluminum c's and knuckles, rear is straight.
axial trans with new outdrives$115 shipped!!!!!!!!!!!!!
1.9 traildocs on black stock car rims. SOLD!!!
U.S only!!!!! paypal only!!!!!